AI Content Improver Free Online

AI Content Improver Free Online — independent reviews, comparisons, pricing and step-by-step guides on Aizhi.

• 

  Radar geo-warping

  Radar geo-warping is the adjustment of geo-referenced radar images and video data to be consistent with a geographical projection. This image warping avoids any restrictions when displaying it together with video from multiple radar sources or with other geographical data including scanned maps and satellite images which may be provided in a particular projection. There are many areas where geo warping has unique benefits: Single radar video signal displayed together with maps of different geographical projections. E.g. Mercator UTM stereographic Multiple radar video signals displayed simultaneously: Having the computing power to do so on one computer. Adapting the projection of all radar signals allowing the geographically correct display and accurate superimposition of those videos. Slant range correction: a modern 3D radar system can measure the height of a target and hence it is possible to correct the radar video by the real corrected range of the target. Slant Range Correction also allows to compensate the radar tower height e.g. for maritime surveillance radars. == Introduction == Radar video presents the echoes of electromagnetic waves a radar system has emitted and received as reflections afterwards. These echoes are typically presented on a computer screen with a color-coding scheme depicting the reflection strength. Two problems have to be solved during such a visualization process. The first problem arises from the fact that typically the radar antenna turns around its position and measures the reflection echo distances from its position in one direction. This effectively means that the radar video data are present in polar coordinates. In older systems the polar oriented picture has been displayed in so called plan position indicators (PPI). The PPI-scope uses a radial sweep pivoting about the center of the presentation. This results in a map-like picture of the area covered by the radar beam. A long-persistence screen is used so that the display remains visible until the sweep passes again. Bearing to the target is indicated by the target's angular position in relation to an imaginary line extending vertically from the sweep origin to the top of the scope. The top of the scope is either true north (when the indicator is operated in the true bearing mode) or ship's heading (when the indicator is operated in the relative bearing mode). For visualization on a modern computer screen the polar coordinates have to be converted into Cartesian coordinates. This process called radar scan conversion is presented with more detail in the next section. The second problem to solve arises from the fact that a radar system is placed in the real world and measures real world echo positions. These echoes have to be displayed together with other real world data like object positions, vector maps and satellite images in a consistent way. All this information refers to the curved earth surface but is displayed on a flat computer display. Building a link from real world earth positions to display pixels is commonly called geographical referencing or in short geo-referencing. Part of the geo-referencing process is to map the 3D earth surface onto a 2D display. This process of a geographical projection can be performed in many ways, but different data sources have their own 'natural' projection. E.g. Cartesian radar video data from a radar source on the earth surface are geo-referenced by a so-called radar projection. When using this radar projection the Cartesian radar video pixels can directly displayed on a computer screen (only being linearly transformed according to the current position on the screen and e.g. the current zoom level). A problem now arises if e.g. also a satellite map shall be shown together with the radar video data. The 'natural' geographical projection of a satellite image would be a satellite projection which depends on the satellite orbit, position and further parameters. Now either the satellite image has to be reprojected to a radar projection or the radar video has to use the satellite projection. This geographical re-projection is also called geographical warping or Geo Warping where each image pixel has to be transformed from one projection into another. This article describes in further detail the Geo Warping of radar video images in real time. It will also show that radar video Geo Warping is done most efficiently when it is integrated with the radar scan conversion process. == Radar-scan conversion == This section describes the principles of the radar-scan conversion (RSC) process. The radar supplies its measured data in polar coordinates (ρ,θ) directly from the rotating antenna. ρ defines the target/echo distance and θ the target angle in polar world coordinates. These data are measured, digitized and stored in a polar coordinate polar store or polar pixmap. The main RSC task is to convert these data to Cartesian (x, y) display coordinates, creating the necessary display pixels. The RSC process is influenced by the current zoom, shift and rotation settings defining which part of the 'world' shall be visible in the display image. As detailed later the RSC process also takes the currently used geographical projection into account when the radar video images are Geo Warped. The OpenGL RSC is implemented using a reverse scan conversion approach which calculates for every image pixel the most appropriate radar amplitude value in the polar store. This approach generates an optimal image without any artifacts known from forward spoke fill algorithms. By applying bi-linear filtering between adjacent pixels in the polar store during the conversion process the OpenGL RSC finally achieves a very high visual quality radar display image for every zoom level, creating smooth images of the radar echoes. == Radar projection == This section illustrates how radar video data are geo referenced and displayed on a computer screen. The radar sensor is positioned on the earth surface with a height h above the ground. It measures the direct distance d to the target (and not e.g. the distance the target is away from the radar if one would move on the earth surface). This distance is then used in the display plane after adjustment to the current display zoom level by the radar scan converter (RSC). Now it has to be clarified how the radar video data is geo referenced. This basically means, that if we want to display a geographical real world object (like e.g. a light house) which is at the same real world position as the radar target, that it also shall appear at the same position in the display plane. This is realized by calculating the distance from the radar sensor to the respective real world object and use that distance in the display plane. The position of the real world object is typically given in geographical coordinates (latitude, longitude and height above the earth surface). In other words, using a radar projection with geographical data is done by simulating a radar measurement process with the real world objects and use the resulting range and azimuth in the display plane. The second picture to the right shows an example radar projection with the center of projection (COP) at latitude 50.0° and longitude 0.0° which is also the radar position. The dashed lines are the equal-latitude and equal-longitude lines on top of the background map. The solid lines show equal-range and equal-azimuth with the respect to the radar position. It is a feature of the radar projection that equal-range lines are circles and equal-azimuth lines are straight lines. This is necessary to display radar video consistently with other map data when using a radar projection where the projection center has to be the radar position. == Geo Warping process == This section explains the actual geo warping or re-projection process when applied to radar video in real time. Assume we want to display radar video on top of a satellite image. As an example we use the CIB projection which is used to display satellite data in CIB (Controlled Image Base) format. The Figure Geo Warping Radar to CIB Projection shows dashed the maximal range circle for a range of 111 km or 60 miles using the radar projection. Such a range is typical for long range coastal surveillance radars. As stated in the last section this is a perfect circle also on the computer screen. The solid line ellipse shows the same range circle for the CIB projection. Typically the errors occurring without Geo Warping are smallest near the radar position if at least the projection center (COP) coincides with the radar position, as realized in our example. Otherwise the error distribution depends both on the used projection and also on the projection parameters. Thus, in our case the errors are most significant near the maximum radar range. The CIB projection error corrected in east–west direction at half the radar range is 2.6 km and is 5.3 km at the full radar range of 111 km. An error of 5.3 km is

  Read more →
• 

  PhotoWorks (ray tracing software)

  PhotoWorks is a raytrace rendering program created by Dassault Systèmes SolidWorks Corporation, formerly supplied as a photorealistic rendering add-in for SolidWorks. The program is based on the Mental Ray rendering engine. It has a library of scenes and materials that can be used with user-created SolidWorks files to create still frame images within the SolidWorks GUI. Since the 2011 release of SolidWorks, PhotoWorks has been replaced by the PhotoView 360 rendering utility. A 2010 review comparing PhotoWorks with three other rendering programs for SolidWorks (including PhotoView 360) gave the program high marks for render speed and built-in materials, but low marks for realism and user interface. Appearance File Type: .p2m

  Read more →
• 

  Image stitching

  Image stitching or photo stitching is the process of combining multiple photographic images with overlapping fields of view to produce a segmented panorama or high-resolution image. Commonly performed through the use of computer software, most approaches to image stitching require nearly exact overlaps between images and identical exposures to produce seamless results, although some stitching algorithms actually benefit from differently exposed images by doing high-dynamic-range imaging in regions of overlap. Some digital cameras can stitch their photos internally. == Applications == Image stitching is widely used in modern applications, such as the following: Document mosaicing Image stabilization feature in camcorders that use frame-rate image alignment High-resolution image mosaics in digital maps and satellite imagery Medical imaging Multiple-image super-resolution imaging Video stitching Object insertion == Process == The image stitching process can be divided into three main components: image registration, calibration, and blending. === Image stitching algorithms === In order to estimate image alignment, algorithms are needed to determine the appropriate mathematical model relating pixel coordinates in one image to pixel coordinates in another. Algorithms that combine direct pixel-to-pixel comparisons with gradient descent (and other optimization techniques) can be used to estimate these parameters. Distinctive features can be found in each image and then efficiently matched to rapidly establish correspondences between pairs of images. When multiple images exist in a panorama, techniques have been developed to compute a globally consistent set of alignments and to efficiently discover which images overlap one another. A final compositing surface onto which to warp or projectively transform and place all of the aligned images is needed, as are algorithms to seamlessly blend the overlapping images, even in the presence of parallax, lens distortion, scene motion, and exposure differences. === Image stitching issues === Since the illumination in two views cannot be guaranteed to be identical, stitching two images could create a visible seam. Other reasons for seams could be the background changing between two images for the same continuous foreground. Other major issues to deal with are the presence of parallax, lens distortion, scene motion, and exposure differences. In a non-ideal real-life case, the intensity varies across the whole scene, and so does the contrast and intensity across frames. Additionally, the aspect ratio of a panorama image needs to be taken into account to create a visually pleasing composite. For panoramic stitching, the ideal set of images will have a reasonable amount of overlap (at least 15–30%) to overcome lens distortion and have enough detectable features. The set of images will have consistent exposure between frames to minimize the probability of seams occurring. === Keypoint detection === Feature detection is necessary to automatically find correspondences between images. Robust correspondences are required in order to estimate the necessary transformation to align an image with the image it is being composited on. Corners, blobs, Harris corners, and differences of Gaussians of Harris corners are good features since they are repeatable and distinct. One of the first operators for interest point detection was developed by Hans Moravec in 1977 for his research involving the automatic navigation of a robot through a clustered environment. Moravec also defined the concept of "points of interest" in an image and concluded these interest points could be used to find matching regions in different images. The Moravec operator is considered to be a corner detector because it defines interest points as points where there are large intensity variations in all directions. This often is the case at corners. However, Moravec was not specifically interested in finding corners, just distinct regions in an image that could be used to register consecutive image frames. Harris and Stephens improved upon Moravec's corner detector by considering the differential of the corner score with respect to direction directly. They needed it as a processing step to build interpretations of a robot's environment based on image sequences. Like Moravec, they needed a method to match corresponding points in consecutive image frames, but were interested in tracking both corners and edges between frames. SIFT and SURF are recent key-point or interest point detector algorithms but a point to note is that SURF is patented and its commercial usage restricted. Once a feature has been detected, a descriptor method like SIFT descriptor can be applied to later match them. === Registration === Image registration involves matching features in a set of images or using direct alignment methods to search for image alignments that minimize the sum of absolute differences between overlapping pixels. When using direct alignment methods one might first calibrate one's images to get better results. Additionally, users may input a rough model of the panorama to help the feature matching stage, so that e.g. only neighboring images are searched for matching features. Since there are smaller group of features for matching, the result of the search is more accurate and execution of the comparison is faster. To estimate a robust model from the data, a common method used is known as RANSAC. The name RANSAC is an abbreviation for "RANdom SAmple Consensus". It is an iterative method for robust parameter estimation to fit mathematical models from sets of observed data points which may contain outliers. The algorithm is non-deterministic in the sense that it produces a reasonable result only with a certain probability, with this probability increasing as more iterations are performed. It being a probabilistic method means that different results will be obtained for every time the algorithm is run. The RANSAC algorithm has found many applications in computer vision, including the simultaneous solving of the correspondence problem and the estimation of the fundamental matrix related to a pair of stereo cameras. The basic assumption of the method is that the data consists of "inliers", i.e., data whose distribution can be explained by some mathematical model, and "outliers" which are data that do not fit the model. Outliers are considered points which come from noise, erroneous measurements, or simply incorrect data. For the problem of homography estimation, RANSAC works by trying to fit several models using some of the point pairs and then checking if the models were able to relate most of the points. The best model – the homography, which produces the highest number of correct matches – is then chosen as the answer for the problem; thus, if the ratio of number of outliers to data points is very low, the RANSAC outputs a decent model fitting the data. === Calibration === Image calibration aims to minimize differences between an ideal lens models and the camera-lens combination that was used, optical defects such as distortions, exposure differences between images, vignetting, camera response and chromatic aberrations. If feature detection methods were used to register images and absolute positions of the features were recorded and saved, stitching software may use the data for geometric optimization of the images in addition to placing the images on the panosphere. Panotools and its various derivative programs use this method. ==== Alignment ==== Alignment may be necessary to transform an image to match the view point of the image it is being composited with. Alignment, in simple terms, is a change in the coordinates system so that it adopts a new coordinate system which outputs image matching the required viewpoint. The types of transformations an image may go through are pure translation, pure rotation, a similarity transform which includes translation, rotation and scaling of the image which needs to be transformed, Affine or projective transform. Projective transformation is the farthest an image can transform (in the set of two dimensional planar transformations), where only visible features that are preserved in the transformed image are straight lines whereas parallelism is maintained in an affine transform. Projective transformation can be mathematically described as x ′ = H ⋅ x , {\displaystyle x'=H\cdot x,} where x {\displaystyle x} is points in the old coordinate system, x ′ {\displaystyle x'} is the corresponding points in the transformed image and H {\displaystyle H} is the homography matrix. Expressing the points x {\displaystyle x} and x ′ {\displaystyle x'} using the camera intrinsics ( K {\displaystyle K} and K ′ {\displaystyle K'} ) and its rotation and translation [ R t ] {\displaystyle [R\,t]} to the real-world coordinates X {\displaystyle X} and < m a t h > x {\displaystyle $x\}\; and\; x\; \prime \; \{\backslash displaystyle\; x\text{'}\}\; \text{'}$, we get Using the abo

  Read more →
• 

  Artisse AI

  Artisse AI is a Hong Kong-based technology company founded by William Wu. The company developed a mobile photography application using generative artificial intelligence to transform selfies into high-quality, personalized images. The app allows users to visualize themselves in various scenarios, outfits, and hairstyles, and they can adjust lighting and ambiance to match their preferences. The app launched in 2023 across multiple markets, including the United States, United Kingdom, Japan, South Korea, Canada, and Australia. By January 2024, users had generated over 5 million images. That same month, the company secured $6.7 million in seed funding to support product development and marketing. == History == Artisse was originally founded in South Korea in 2022 by William Wu. The early concept was connected to a virtual idol initiative developed in collaboration with a K-pop agency, intended to support Wu's blockchain gaming business. The project later evolved into a standalone AI photography application. The current version of the Artisse app was developed following the company's relocation to Hong Kong in 2022. In January 2024, Artisse secured $6.7 million in seed funding, led by The London Fund. The investment was aimed at supporting product development, marketing, and user acquisition. Artisse uses an AI algorithm to create hyperrealistic images from uploaded photos. The app generates personalized images by combining generative AI technology, a global pool of licensed talent, and finished art services. The app works with individual users and businesses, offering professional-grade photos and advertisement images. According to the British newspaper Evening Standard the company has developed the world's first and most advanced AI photographer. It captures 15-30 photos of the user and generates 2D images, placing them in various outfits and locations worldwide. === Catheron Gaming === Artisse AI originated from Catheon Gaming, a blockchain gaming and entertainment company founded in 2021 by William Wu. Catheon Gaming published more than 30 Web3 titles in its first year, developed a blockchain game distribution platform, and offered advisory services to external developers. In 2022, HSBC and KPMG listed Catheon Gaming among the "Top 10 Emerging Giants" in the Asia–Pacific region, selected from a pool of more than 6,000 startups. In June 2023, Catheon Gaming was rebranded as Artisse Interactive, creating two divisions: Artisse Gaming, which continued blockchain and Web3 game development, and Artisse AI, which focused on generative photography technology. == Technology == Artisse uses a proprietary generative AI model combined with open-source imaging frameworks and diffusion models. Users are prompted to upload between 15 and 30 personal images, allowing the AI to train a personalized model in 30 to 40 minutes. After training, the app generates new images based on either textual or visual prompts, with options to adjust elements such as clothing, hairstyles, lighting, and backgrounds. To enhance realism, the app integrates augmented reality features and image refinement tools. The company has introduced features to address representation issues related to body shape and skin tone, although concerns persist about the ethical implications of altering personal traits. == Products == === Artisse mobile app === Available on iOS and Android platforms in 35 languages. Users initially receive 25 free images, after which the app adopts a subscription pricing model ranging from approximately $6 to $30 per month. By early 2024, the app reported around 4,000 paying subscribers out of more than 200,000 downloads. === Business and enterprise services === Artisse provides B2B solutions for creating marketing imagery and partners with agencies like Iconic Management to enable cost-effective virtual photoshoots. Additional features in development include virtual try-on capabilities and augmented reality integration for fashion retail. == Reception == Media coverage has noted the app's photorealistic image outputs with some sources highlighting its ease of use. However, concerns have been raised regarding image authenticity, algorithmic biases, and the potential impact on professional photography and modeling. Artisse has been widely covered by media outlets including TechCrunch, PetaPixel, Forbes Australia, and The Evening Standard. These publications discussed the app's integration of generative AI technology within the consumer photography space, its growing market influence, and its rapid adoption by users worldwide.

  Read more →
• 

  Automatic meter reading

  Automatic meter reading (AMR) is the technology of automatically collecting consumption, diagnostic, and status data from water meter or energy metering devices (gas, electric) and transferring that data to a central database for billing, troubleshooting, and analyzing. This technology mainly saves utility providers the expense of periodic trips to each physical location to read a meter. Another advantage is that billing can be based on near real-time consumption rather than on estimates based on past or predicted consumption. This timely information coupled with analysis can help both utility providers and customers better control the use and production of electric energy, gas usage, or water consumption. AMR technologies include handheld, mobile and network technologies based on telephony platforms (wired and wireless), radio frequency (RF), or powerline transmission. == Technologies == === Touch technology === With touch-based AMR, a meter reader carries a handheld computer or data collection device with a wand or probe. The device automatically collects the readings from a meter by touching or placing the read probe close to a reading coil enclosed in the touchpad. When a button is pressed, the probe sends an interrogate signal to the touch module to collect the meter reading. The software in the device matches the serial number to one in the route database, and saves the meter reading for later download to a billing or data collection computer. Since the meter reader still has to go to the site of the meter, this is sometimes referred to as "on-site" AMR. Another form of contact reader uses a standardized infrared port to transmit data. Protocols are standardized between manufacturers by such documents as ANSI C12.18 or IEC 61107. === AMR hosting === AMR hosting is a back-office solution which allows a user to track their electricity, water, or gas consumption over the Internet. All data is collected in near real-time, and is stored in a database by data acquisition software. The user can view the data via a web application, and can analyze the data using various online analysis tools such as charting load profiles, analyzing tariff components, and verify their utility bill. === Radio frequency network === Radio frequency based AMR can take many forms. The more common ones are handheld, mobile, satellite and fixed network solutions. There are both two-way RF systems and one-way RF systems in use that use both licensed and unlicensed RF bands. In a two-way or "wake up" system, a radio signal is normally sent to an AMR meter's unique serial number, instructing its transceiver to power-up and transmit its data. The meter transceiver and the reading transceiver both send and receive radio signals. In a one-way "bubble-up" or continuous broadcast type system, the meter transmits continuously and data is sent every few seconds. This means the reading device can be a receiver only, and the meter a transmitter only. Data travels only from the meter transmitter to the reading receiver. There are also hybrid systems that combine one-way and two-way techniques, using one-way communication for reading and two-way communication for programming functions. RF-based meter reading usually eliminates the need for the meter reader to enter the property or home, or to locate and open an underground meter pit. The utility saves money by increased speed of reading, has less liability from entering private property, and has fewer missed readings from being unable to access the meter. The technology based on RF is not readily accepted everywhere. In several Asian countries, the technology faces a barrier of regulations in place pertaining to use of the radio frequency of any radiated power. For example, in India the radio frequency which is generally in ISM band is not free to use even for low power radio of 10 mW. The majority of manufacturers of electricity meters have radio frequency devices in the frequency band of 433/868 MHz for large scale deployment in European countries. The frequency band of 2.4 GHz can be now used in India for outdoor as well as indoor applications, but few manufacturers have shown products within this frequency band. Initiatives in radio frequency AMR in such countries are being taken up with regulators wherever the cost of licensing outweighs the benefits of AMR. ==== Handheld ==== In handheld AMR, a meter reader carries a handheld computer with a built-in or attached receiver/transceiver (radio frequency or touch) to collect meter readings from an AMR capable meter. This is sometimes referred to as "walk-by" meter reading since the meter reader walks by the locations where meters are installed as they go through their meter reading route. Handheld computers may also be used to manually enter readings without the use of AMR technology as an alternate but this will not support exhaustive data which can be accurately read using the meter reading electronically. ==== Mobile ==== Mobile or "drive-by" meter reading is where a reading device is installed in a vehicle. The meter reader drives the vehicle while the reading device automatically collects the meter readings. Often, for mobile meter reading, the reading equipment includes navigational and mapping features provided by GPS and mapping software. With mobile meter reading, the reader does not normally have to read the meters in any particular route order, but just drives the service area until all meters are read. Components often consist of a laptop or proprietary computer, software, RF receiver/transceiver, and external vehicle antennas. ==== Satellite ==== Transmitters for data collection satellites can be installed in the field next to existing meters. The satellite AMR devices communicate with the meter for readings, and then sends those readings over a fixed or mobile satellite network. This network requires a clear view to the sky for the satellite transmitter/receiver, but eliminates the need to install fixed towers or send out field technicians, thereby being particularly suited for areas with low geographic meter density. ==== RF technologies commonly used for AMR ==== Narrow Band (single fixed radio frequency) Spread spectrum Direct-sequence spread spectrum (DSSS) Frequency-hopping spread spectrum (FHSS) There are also meters using AMR with RF technologies such as cellular phone data systems, Zigbee, Bluetooth, Wavenis and others. Some systems operate with U.S. Federal Communications Commission (FCC) licensed frequencies and others under FCC Part 15, which allows use of unlicensed radio frequencies. ==== Wi-Fi ==== WiSmart is a versatile platform which can be used by a variety of electrical home appliances in order to provide wireless TCP/IP communication using the 802.11 b/g protocol. Devices such as the Smart Thermostat permit a utility to lower a home's power consumption to help manage power demand. The city of Corpus Christi became one of the first cities in the United States to implement citywide Wi-Fi, which had been free until May 31, 2007, mainly to facilitate AMR after a meter reader was attacked by a dog. Today many meters are designed to transmit using Wi-Fi, even if a Wi-Fi network is not available, and they are read using a drive-by local Wi-Fi hand held receiver. The meters installed in Corpus Christi are not directly Wi-Fi enabled, but rather transmit narrow-band burst telemetry on the 460 MHz band. This narrow-band signal has much greater range than Wi-Fi, so the number of receivers required for the project are far fewer. Special receiver stations then decode the narrow-band signals and resend the data via Wi-Fi. Most of the automated utility meters installed in the Corpus Christi area are battery powered. Wi-Fi technology is unsuitable for long-term battery-powered operation. === Power line communication === PLC is a method where electronic data is transmitted over power lines back to the substation, then relayed to a central computer in the utility's main office. This would be considered a type of fixed network system—the network being the distribution network which the utility has built and maintains to deliver electric power. Such systems are primarily used for electric meter reading. Some providers have interfaced gas and water meters to feed into a PLC type system. == Brief history == In 1972, Theodore George "Ted" Paraskevakos, while working with Boeing in Huntsville, Alabama, developed a sensor monitoring system which used digital transmission for security, fire and medical alarm systems as well as meter reading capabilities for all utilities. This technology was a spin-off of the automatic telephone line identification system, now known as caller ID. In 1974, Paraskevakos was awarded a U.S. patent for this technology. In 1977, he launched Metretek, Inc., which developed and produced the first fully automated, commercially available remote meter reading and load management system. Since this system was developed pre-Internet, Metret

  Read more →
• 

  Artbreeder

  Artbreeder, formerly known as Ganbreeder, is a collaborative, machine learning-based art website. Using the models StyleGAN and BigGAN, the website allows users to generate and modify images of faces, landscapes, and paintings, among other categories. == Overview == On Artbreeder, users mainly interact through the remixing - referred to as 'breeding' - of other users' images found in the publicly accessible database of images. The creation of new variations can be done by tweaking sliders on an image's page, known as "genes", which in the "Portraits" model can range from color balance to gender, facial hair, and glasses. Additionally, any image can be "crossbred" with other publicly viewable images from the database, using a slider to control how much of each image should influence the resulting "child". The site also allows for uploading new images, which the model will attempt to convert into the latent space of the network. == Notable usages == The similarly AI-driven text adventure game AI Dungeon uses Artbreeder to generate profile pictures for its users, and The Static Age's Andrew Paley has used Artbreeder to create the visuals for his music videos. Artbreeder has been used to create portraits of characters from popular novels such as Harry Potter and Twilight. They have also been used to add realistic features to ancient portraits. Artbreeder was used to create characters in the sequel to Ben Drowned with the titular villain, an AI-construct itself, created entirely using the website. == Changes to Artbreeder == ArtBreeder underwent an overhaul, introducing several features to enhance the user experience. Among these updates is the integration SD-XL, developed by stability.ai. Additionally, ArtBreeder also added a functionality known as ControlNet, which enables users to create images based on specific poses. With ControlNet, users can incorporate various poses into their AI Artworks. More features that were introduced into Artbreeder, are Pattern, which creates AI Pattern Images, Outpainting or Uncropping was also an added feature to Artbreeder, that allows the user to expand the image beyond the normal dimensions of the image. == Reception == The artwork generated by users of the website has been described as "beautiful" and "surreal," drawing comparisons to "weird, incomprehensible dreams" that "somehow touch the deep, unconscious parts of [the] mind". However, the generated faces were noted as "creepy and 'off'", and still nowhere near the quality attained by actual digital artists. Additionally, the site faced criticism for perceived confusing aspects of the AI's behavior. Jonathan Bartlett of Mind Matters News noted that "As is always the case with AI, sometimes the [gene] knobs don't work as expected and sometimes the results are... strange," while conceding that Artbreeder was still "probably the start of a new future of made-to-order stock images." Writers from Hyperallergic also took issue with perceived racial biases in the Portraits model, citing a comment from a user who faced difficulty from the neural network while attempting to darken the skin of a portrait to match a source image.

  Read more →
• 

  Act! LLC

  ACT! (previously known as Activity Control Technology, Automated Contact Tracking, ACT! by Sage, and Sage ACT!) is a customer relationship management and marketing automation software platform designed for small and medium-sized businesses. It has over 2.8 million registered users as of December 2014. == History == The company Conductor Software was founded in 1986, in Dallas, Texas, by Pat Sullivan and Mike Muhney. The original name for the software was Activity Control Technology; it was renamed to Automated Contact Tracking, later abbreviated to ACT. The name of the company was subsequently changed to Contact Software International and it was sold in 1993 to Symantec Corporation, who in 1999 then sold it to SalesLogix. The Sage Group purchased Interact Commerce (formerly SalesLogix) in 2001 through Best Software, then its North American software division. Swiftpage acquired it in 2013. Beginning with the 2006 version, the name was styled ACT! by Sage, and in 2010 revised to Sage ACT!. Following its 2013 acquisition by Swiftpage, it was renamed to ACT! Swiftpage. In May 2018, ACT! was sold to SFW Advisors. In December 2018, Kuvana, a marketing automation software solution, was acquired by SFW and merged with ACT! This add-on is now a complementary service to the core CRM solution. In December 2019, ACT! hired Steve Oriola as chairman and CEO. In 2020, Swiftpage changed its company name to ACT!. In March 2023, ACT! hired Bruce Reading as President and CEO. == Software == ACT! features include contact, company and opportunity management, a calendar, marketing automation and e-marketing tools, reports, interactive dashboards with graphical visualizations, and the ability to track prospective customers. ACT! integrates with Microsoft Word, Excel, Outlook, Google Contacts, Gmail, and other applications via Zapier. For custom integrations, ACT! has an in-built API. ACT! can be accessed from Windows desktops (Win7 and later) with local or network shared database; synchronized to laptops or remote officers; Citrix or Remote Desktop; Web browsers (Premium only) with self or SaaS hosting; smartphones and tablets via HTML5 Web (Premium only); smartphones and tablets via sync with Handheld Contact.

  Read more →
• 

  VGACAD

  VGACAD was the parent of a suite of shareware graphic utilities made for the MS-DOS operating system used in the IBM PC and clones. It was popular for editing and capturing images using BSAVE (graphics image format) and provided an early graphic editing suite compatible with multiple graphic cards and resolutions, used on the IBM PC. == Usage == Written by Lawrence Gozum in 1987, it was the genesis of multiple versions and improvements over 10 years. Ran with his brother, Marvin initially helped with design ideas, strategic focus, technical support calls, and managing the early shareware business. The growth of the VGACAD suite grew quickly to preoccupy most of their time. Lawrence then focused more of his efforts on software and formed Applied Insights, to manage VGACAD and its offspring, VidFun, and Ai Picture Explorer. At its peak, its users ranged from individuals, Federal government offices, museums and major newspapers. == Features == VGACAD was a misnomer, and meant VGA-Computer Assisted Drawing, rather than computer-aided design, as CAD is commonly referred to today. Its longevity was due to its color accuracy, speed, small size, and that its suite of small utilities often worked stand-alone. One called VGACAP, for 'capture', dumped video memory into a file that could later be converted to popular graphic image formats, later made commonplace when Microsoft Windows programmed the print screen key to dump graphics into the clipboard. However, VGACAP ran insulated apart from early versions of Windows, and thus could capture screens were applications prohibited such function.

  Read more →
• 

  DigitaltMuseum

  DigitaltMuseum (lit. 'The Digital Museum') is a website database in Norwegian and Swedish for art, images and cultural history museums. The service was established in 2009 after a trial period. The database is developed and operated by KulturIT. KulturIT ANS was established by the Norwegian Museum of Cultural History and Maihaugen in consultation with the Norwegian Archive, Library and Museum Authority (ABM) in 2007. In 2015, the company underwent a corporate transformation and KulturIT AS was established on 12 February. The website has per 2025 around 2,548,022 images. Many of the images are in the public domain or under Creative Commons licenses and are being imported into Wikimedia Commons. The website's API was developed in 2012. == Institutions == As of 2025, there are 223 collaborating museums. == Mission == DigitaltMuseum aims to make the museums' collections accessible to all interested parties, regardless of time and place. The website aims to facilitate easy use of the collections through various methods including image searches, research, teaching and joint knowledge development. DigitaltMuseum contains collections from several hundred Norwegian and Swedish museums, totalling around five million objects. The website contains both historical images from the areas and themes covered by the museums, as well as images of artefacts from the collections. Parts of the collection have previously only been shown in the museums' exhibitions and books and have therefore rarely or never been shown to the public.

  Read more →
• 

  AARON

  AARON is the collective name for a series of computer programs written by artist Harold Cohen that create original artistic images autonomously, which set it apart from previous programs. Proceeding from Cohen's initial question "What are the minimum conditions under which a set of marks functions as an image?", AARON was in development between 1972 and the 2010s. As the software is not open source, its development effectively ended with Cohen's death in 2016. The name "AARON" does not seem to be an acronym; rather, it was a name chosen to start with the letter "A" so that the names of successive programs could follow it alphabetically. However, Cohen did not create any other major programs. Initial versions of AARON created abstract drawings that grew more complex through the 1970s. More representational imagery was added in the 1980s; first rocks, then plants, then people. In the 1990s more representational figures set in interior scenes were added, along with color. AARON returned to more abstract imagery, this time in color, in the early 2000s. Cohen used machines that allowed AARON to produce physical artwork. The first machines drew in black and white using a succession of custom-built "turtle" and flatbed plotter devices. Cohen would sometimes color these images by hand in fabric dye (Procion), or scale them up to make larger paintings and murals. In the 1990s Cohen built a series of digital painting machines to output AARON's images in ink and fabric dye. His later work used a large-scale inkjet printer on canvas. Development of AARON began in the C programming language then switched to Lisp in the early 1990s. Cohen credits Lisp with helping him solve the challenges he faced in adding color capabilities to AARON. An article about Cohen appeared in Computer Answers that describes AARON and shows two line drawings that were exhibited at the Tate gallery. The article goes on to describe the workings of AARON, then running on a DEC VAX 750 minicomputer. Raymond Kurzweil's company has produced a downloadable screensaver of AARON for Microsoft Windows PCs. This version of AARON can also produce printable images. AARON's source code is not publicly available, but Cohen has described AARON's operations in various essays and it is discussed in abstract in Pamela McCorduck's book. AARON cannot learn new styles or imagery on its own; each new capability must be hand-coded by Cohen. It is capable of producing a practically infinite supply of distinct images in its own style. Examples of these images have been exhibited in galleries worldwide. AARON's artwork has been used as an artistic equivalent of the Turing test. It does seem however that AARON's output follows a noticeable formula (figures standing next to a potted plant, framed within a colored square is a common theme). Cohen is very careful not to claim that AARON is creative. But he does ask "If what AARON is making is not art, what is it exactly, and in what ways, other than its origin, does it differ from the 'real thing?' If it is not thinking, what exactly is it doing?" — The further exploits of AARON, Painter. The Whitney Museum featured AARON in 2024, showcasing the evolution of AARON as the earliest artificial intelligence (AI) program for artmaking.

  Read more →
• 

  Image subtraction

  Image subtraction or pixel subtraction or difference imaging is an image processing technique whereby the digital numeric value of one pixel or whole image is subtracted from another image, and a new image generated from the result. This is primarily done for one of two reasons – levelling uneven sections of an image such as half an image having a shadow on it, or detecting changes between two images. This method can show things in the image that have changed position, brightness, color, or shape. For this technique to work, the two images must first be spatially aligned to match features between them, and their photometric values and point spread functions must be made compatible, either by careful calibration, or by post-processing (using color mapping). The complexity of the pre-processing needed before differencing varies with the type of image, but is essential to ensure good subtraction of static features. This is commonly used in fields such as time-domain astronomy (known primarily as difference imaging) to find objects that fluctuate in brightness or move. In automated searches for asteroids or Kuiper belt objects, the target moves and will be in one place in one image, and in another place in a reference image made an hour or day later. Thus, image processing algorithms can make the fixed stars in the background disappear, leaving only the target. Distinct families of astronomical image subtraction techniques have emerged, operating in both image space or frequency space, with distinct trade-offs in both quality of subtraction and computational cost. These algorithms lie at the heart of almost all modern (and upcoming) transient surveys, and can enable the detection of even faint supernovae embedded in bright galaxies. Nevertheless, in astronomical imaging, significant 'residuals' remain around bright, complex sources, necessitating further algorithmic steps to identify candidates (known as real-bogus classification) The Hutchinson metric can be used to "measure of the discrepancy between two images for use in fractal image processing".

  Read more →
• 

  PhotoWorks (ray tracing software)

  PhotoWorks is a raytrace rendering program created by Dassault Systèmes SolidWorks Corporation, formerly supplied as a photorealistic rendering add-in for SolidWorks. The program is based on the Mental Ray rendering engine. It has a library of scenes and materials that can be used with user-created SolidWorks files to create still frame images within the SolidWorks GUI. Since the 2011 release of SolidWorks, PhotoWorks has been replaced by the PhotoView 360 rendering utility. A 2010 review comparing PhotoWorks with three other rendering programs for SolidWorks (including PhotoView 360) gave the program high marks for render speed and built-in materials, but low marks for realism and user interface. Appearance File Type: .p2m

  Read more →
• 

  Materialized view

  In computing, a materialized view is a database object that contains the results of a query. For example, it may be a local copy of data located remotely, or may be a subset of the rows and/or columns of a table or join result, or may be a summary using an aggregate function. The process of setting up a materialized view is sometimes called materialization. This is a form of caching the results of a query, similar to memoization of the value of a function in functional languages, and it is sometimes described as a form of precomputation. As with other forms of precomputation, database users typically use materialized views for performance reasons, i.e. as a form of optimization. Materialized views that store data based on remote tables were also known as snapshots (deprecated Oracle terminology). In any database management system following the relational model, a view is a virtual table representing the result of a database query. Whenever a query or an update addresses an ordinary view's virtual table, the DBMS converts these into queries or updates against the underlying base tables. A materialized view takes a different approach: the query result is cached as a concrete ("materialized") table (rather than a view as such) that may be updated from the original base tables from time to time. This enables much more efficient access, at the cost of extra storage and of some data being potentially out-of-date. Materialized views find use especially in data warehousing scenarios, where frequent queries of the actual base tables can be expensive. In a materialized view, indexes can be built on any column. In contrast, in a normal view, it's typically only possible to exploit indexes on columns that come directly from (or have a mapping to) indexed columns in the base tables; often this functionality is not offered at all. == Implementations == === Oracle === Materialized views were implemented first by the Oracle Database: the Query rewrite feature was added from version 8i. Example syntax to create a materialized view in Oracle: === PostgreSQL === In PostgreSQL, version 9.3 and newer natively support materialized views. In version 9.3, a materialized view is not auto-refreshed, and is populated only at time of creation (unless WITH NO DATA is used). It may be refreshed later manually using REFRESH MATERIALIZED VIEW. In version 9.4, the refresh may be concurrent with selects on the materialized view if CONCURRENTLY is used. Example syntax to create a materialized view in PostgreSQL: === SQL Server === Microsoft SQL Server differs from other RDBMS by the way of implementing materialized view via a concept known as "Indexed Views". The main difference is that such views do not require a refresh because they are in fact always synchronized to the original data of the tables that compound the view. To achieve this, it is necessary that the lines of origin and destination are "deterministic" in their mapping, which limits the types of possible queries to do this. This mechanism has been realised since the 2000 version of SQL Server. Example syntax to create a materialized view in SQL Server: === Stream processing frameworks === Apache Kafka (since v0.10.2), Apache Spark (since v2.0), Apache Flink, Kinetica DB, Materialize, RisingWave, and Epsio all support materialized views on streams of data. === Others === Materialized views are also supported in Sybase SQL Anywhere. In IBM Db2, they are called "materialized query tables". ClickHouse supports materialized views that automatically refresh on merges. MySQL doesn't support materialized views natively, but workarounds can be implemented by using triggers or stored procedures or by using the open-source application Flexviews. Materialized views can be implemented in Amazon DynamoDB using data modification events captured by DynamoDB Streams. Google announced in 8 April 2020 the availability of materialized views for BigQuery as a beta release.

  Read more →
• 

  Deluxe Paint

  Deluxe Paint, often referred to as DPaint, is a bitmap graphics editor created by Dan Silva for Electronic Arts and published for the then-new Amiga 1000 in November 1985. A series of updated versions followed, some of which were ported to other platforms. An MS-DOS release with support for the 256 color VGA standard became popular for creating pixel graphics in video games in the 1990s. Author Dan Silva previously worked on the Cut & Paste word processor (1984), also from Electronic Arts. == History == Deluxe Paint began as an in-house art development tool called Prism. As author Dan Silva added features to Prism, it was developed as a showcase product to coincide with the Amiga's debut in 1985. Upon release, it was quickly embraced by the Amiga community and became the de facto graphics (and later animation) editor for the platform. Amiga manufacturer Commodore International later commissioned EA to create version 4.5 AGA to bundle with the new Advanced Graphics Architecture chipset (A1200, A4000) capable Amigas. Version 5 was the last release after Commodore's bankruptcy in 1994. Early versions of Deluxe Paint were available in protected and non copy-protected versions, the latter retailing for a slightly higher price. The copy protection scheme was later dropped. Deluxe Paint was first in a series of products from the Electronic Arts Tools group—then later moved to the ICE (for Interactivity, Creativity, and Education) group—which included such Amiga programs as Deluxe Music Construction Set (preceded by Music Construction Set for the Apple II), Deluxe Video, and the Studio series of paint programs for the Mac. With the development of Deluxe Paint, EA introduced the ILBM and ANIM file format standards for graphics. While widely used on the Amiga, these formats never gained widespread end user acceptance on other platforms, but were heavily used by game development companies. Deluxe Paint was used by LucasArts to make graphics for their adventure games such as The Secret of Monkey Island, and the name of a particular filename used to store the main protagonist Guybrush Threepwood was probably at the origin of his peculiar name. One of the main artist developer of the game, Mark Ferrari, in an interview for The Making of Monkey Island 30th Anniversary Documentary remembers that "there was a pulldown menu in DPaint called brushes, so character sprites were referred to as brushes", and the male protagonist was simply "the guy.brush" until the artist Steve Purcell suggested to take the very name "Guybrush". The author Ron Gilbert remembers that the PC DOS version of the file was named "guybrush.bbm". == Versions == === Amiga === Deluxe Paint I was released in 1985. A major feature was animation by using color cycling. The Amiga natively supports indexed color, where a pixel's color value does not carry any RGB hue information but instead is an index to a color palette (a collection of unique color values). By adjusting the color value in the palette, all pixels with that palette value change simultaneously in the image or animation, creating cyclic movement in the image. In the Christmas demo files on the Deluxe Paint I disk, this kind of animation (which is toggled by pressing the tab key) is used to depict falling snowflakes, a blinking Christmas tree, and a roaring fire in the fireplace. In 1986, Deluxe Paint II was introduced, which added many convenient features such as pattern and gradient fill, which could be selected by right-clicking on a fill tool. An effects menu with e.g. perspective transformation was also added. The screen format could now be changed from a dedicated selection page. Deluxe Paint III appeared in 1989 and added support for Extra Halfbrite. New editing modes allowed one to stencil certain colors to protect them, so it is possible to e.g. paint a landscape from front to back, with the foreground protected by a stencil. A major new feature of Deluxe Paint III was the ability to create cel-like animation, and animbrushes (1MB of RAM is needed for animation). These let the user pick up a section of an animation as an "animbrush", which can then be placed onto the canvas while it animates. Deluxe Paint III was one of the first paint programs to support animbrushes. This is similar to copy and paste, except one can pick up more than one image. Deluxe Paint IV (introduced in 1991), which did not include Silva as the lead programmer, offered significant new features like non-bitplane-indexed Hold-and-Modify support for creating images with up to 4,096 colors. Animation support was improved by adding a light table, i.e. onion skinning, and AnimBrush morphing. The color mixer was now a HAM region at the bottom of the screen (instead of a floating window as before) and allowed mixing adjacent colors similar to a real palette. Deluxe Paint 4.5 AGA appeared the following year, addressing the stability issues and providing support for the new A1200 and A4000 AGA machines and a revamped screen mode interface. It appeared in both standalone and Commodore-bundled versions. The final release, Deluxe Paint V, in 1995, supported true 24-bit RGB images. However, using only the AGA native chipset, the 24-bit RGB color was only held in computer memory, the on-screen image was displayed in HAM8 (18-bit color). === Apple IIGS === DeluxePaint II for the Apple IIGS was developed by Brent Iverson and released in 1987. === MS-DOS === Deluxe Paint II for MS-DOS was released in 1988, It required MS-DOS 2.0 and 640 kB of RAM. It supports CGA, EGA, MCGA, VGA, Hercules and Tandy IBM PC-compatible graphic cards. Deluxe Paint II Enhanced was released in 1989, requiring MS-DOS 2.11 and 640 kB of RAM. It supports resolutions up to 800x600 pixels with 256 colors. Deluxe Paint II Enhanced 2.0, released in 1994, was the most successful MS-DOS version, and was compatible with PC Paintbrush PCX image files. The MS-DOS conversion was done by Brent Iverson with the enhanced features by Steve Shaw. It supports CGA, EGA, MCGA, VGA, Hercules, Tandy, and Amstrad video cards, as well as early Super VGA video cards enabling it to support up to 800 × 600 with 256 (from 262,144) colors and 1024 × 768 with 16 colors. The sister product Deluxe Paint Animation (only for 320×200 pixels and 256 colors) was widely used, especially in video game development. === Atari ST === Deluxe Paint ST was developed by ArtisTech Development, published by Electronic Arts, and was released in 1990. It supports the Atari STE 4096 color palette and animated graphics. Features advertised for the Atari ST version include 3D perspective, design your own fonts, mirror symmetry, multi-color airbrushing & animations, printing up to poster size, split-screen magnification with variable zoom, and working on animations (including multiple animations). == Workflow == "[" and "]" hotkeys step through the indexed palette, turning indexed-pixel-painting into a fast two-handed mouse+keys process, and the right mouse button paints with the background color. For example, transparency is obtained as simply as selecting a background color index (a single right click on the palette GUI to change). colors could be locked from editing by use of a stencil (a list of color indices whose pixels should not be altered in the image data) and simple color-cycling animations could be created using contiguous entries in the palette. This was easy to change the hue and tone of a section of the image by altering the corresponding colors in the palette. (The specific section needed to use a dedicated part of the palette for this technique to work.) Brushes can be cut from the background by using the box, freehand, or polygon selection tools. They can then be used in the same manner as any other brush or pen. This functionality is simpler to use than the "stamp" tool of Photoshop or Alpha Channels as provided in later programs. Brushes can be rotated and scaled, even in 3D. After a brush is selected, it appears attached to the mouse cursor, providing an exact preview of what will be drawn. This allows precise pixel positioning of brushes. Animations stored in IFF ANIM format are delta compressed making animations both smaller and faster to playback. == Reception == Compute! criticized the documentation of the first release of DeluxePaint as inadequate, but stated that "DeluxePaint is a visual arts program of immense scope and flexibility". In later versions the documentation was much improved; for instance DeluxePaint IV came with a 300-page manual. Deluxe Paint was a hit for EA. The main line of the series, particularly installments one to three, has won a total of at least nine awards from independent publications and organizations, including three Amiga-specific awards. Deluxe Paint III also won Commodore International's Enterprise and Vision award in 1990, becoming the first software to win the award, for what the company's judges believed to be best utilizing the Amiga's graphical capabilities. Deluxe Pai

  Read more →
• 

  List of robotics journals

  List of robotics journals includes notable academic and scientific journals that focus on research in the field of robotics and automation. == Journals == Acta Mechanica et Automatica Advanced Robotics Annual Review of Control, Robotics, and Autonomous Systems IEEE Robotics and Automation Letters IEEE Transactions on Robotics IEEE Transactions on Field Robotics The International Journal of Advanced Manufacturing Technology International Journal of Humanoid Robotics International Journal of Robotics Research Journal of Cognitive Engineering and Decision Making Journal of Field Robotics Journal of Intelligent & Robotic Systems Paladyn Robotics and Autonomous Systems Robotics Science Robotics SLAS Technology

  Read more →