AI Grammar Rephrase

AI Grammar Rephrase — independent reviews, comparisons, pricing and step-by-step guides on Aizhi.

• 

  Shape factor (image analysis and microscopy)

  Shape factors are dimensionless quantities used in image analysis and microscopy that numerically describe the shape of a particle, independent of its size. Shape factors are calculated from measured dimensions, such as diameter, chord lengths, area, perimeter, centroid, moments, etc. The dimensions of the particles are usually measured from two-dimensional cross-sections or projections, as in a microscope field, but shape factors also apply to three-dimensional objects. The particles could be the grains in a metallurgical or ceramic microstructure, or the microorganisms in a culture, for example. The dimensionless quantities often represent the degree of deviation from an ideal shape, such as a circle, sphere or equilateral polyhedron. Shape factors are often normalized, that is, the value ranges from zero to one. A shape factor equal to one usually represents an ideal case or maximum symmetry, such as a circle, sphere, square or cube. == Aspect ratio == The most common shape factor is the aspect ratio, a function of the largest diameter and the smallest diameter orthogonal to it: A R = d min d max {\displaystyle A_{R}={\frac {d_{\min }}{d_{\max }}}} The normalized aspect ratio varies from approaching zero for a very elongated particle, such as a grain in a cold-worked metal, to near unity for an equiaxed grain. The reciprocal of the right side of the above equation is also used, such that the AR varies from one to approaching infinity. == Circularity == Another very common shape factor is the circularity (or isoperimetric quotient), a function of the perimeter P and the area A: f circ = 4 π A P 2 {\displaystyle f_{\text{circ}}={\frac {4\pi A}{P^{2}}}} The circularity of a circle is 1, and much less than one for a starfish footprint. The reciprocal of the circularity equation is also used, such that fcirc varies from one for a circle to infinity. == Elongation shape factor == The less-common elongation shape factor is defined as the square root of the ratio of the two second moments in of the particle around its principal axes. f elong = i 2 i 1 {\displaystyle f_{\text{elong}}={\sqrt {\frac {i_{2}}{i_{1}}}}} == Compactness shape factor == The compactness shape factor is a function of the polar second moment in of a particle and a circle of equal area A. f comp = A 2 2 π i 1 2 + i 2 2 {\displaystyle f_{\text{comp}}={\frac {A^{2}}{2\pi {\sqrt {{i_{1}}^{2}+{i_{2}}^{2}}}}}} The fcomp of a circle is one, and much less than one for the cross-section of an I-beam. == Waviness shape factor == The waviness shape factor of the perimeter is a function of the convex portion Pcvx of the perimeter to the total. f wav = P cvx P {\displaystyle f_{\text{wav}}={\frac {P_{\text{cvx}}}{P}}} Some properties of metals and ceramics, such as fracture toughness, have been linked to grain shapes. == An application of shape factors == Greenland, the largest island in the world, has an area of 2,166,086 km2; a coastline (perimeter) of 39,330 km; a north–south length of 2670 km; and an east–west length of 1290 km. The aspect ratio of Greenland is A R = 1290 2670 = 0.483 {\displaystyle A_{R}={\frac {1290}{2670}}=0.483} The circularity of Greenland is f circ = 4 π ( 2166086 ) 39330 2 = 0.0176. {\displaystyle f_{\text{circ}}={\frac {4\pi (2166086)}{39330^{2}}}=0.0176.} The aspect ratio is agreeable with an eyeball-estimate on a globe. Such an estimate on a typical flat map, using the Mercator projection, would be less accurate due to the distorted scale at high latitudes. The circularity is deceptively low, due to the fjords that give Greenland a very jagged coastline (see the coastline paradox). A low value of circularity does not necessarily indicate a lack of symmetry, and shape factors are not limited to microscopic objects.

  Read more →
• 

  Artbreeder

  Artbreeder, formerly known as Ganbreeder, is a collaborative, machine learning-based art website. Using the models StyleGAN and BigGAN, the website allows users to generate and modify images of faces, landscapes, and paintings, among other categories. == Overview == On Artbreeder, users mainly interact through the remixing - referred to as 'breeding' - of other users' images found in the publicly accessible database of images. The creation of new variations can be done by tweaking sliders on an image's page, known as "genes", which in the "Portraits" model can range from color balance to gender, facial hair, and glasses. Additionally, any image can be "crossbred" with other publicly viewable images from the database, using a slider to control how much of each image should influence the resulting "child". The site also allows for uploading new images, which the model will attempt to convert into the latent space of the network. == Notable usages == The similarly AI-driven text adventure game AI Dungeon uses Artbreeder to generate profile pictures for its users, and The Static Age's Andrew Paley has used Artbreeder to create the visuals for his music videos. Artbreeder has been used to create portraits of characters from popular novels such as Harry Potter and Twilight. They have also been used to add realistic features to ancient portraits. Artbreeder was used to create characters in the sequel to Ben Drowned with the titular villain, an AI-construct itself, created entirely using the website. == Changes to Artbreeder == ArtBreeder underwent an overhaul, introducing several features to enhance the user experience. Among these updates is the integration SD-XL, developed by stability.ai. Additionally, ArtBreeder also added a functionality known as ControlNet, which enables users to create images based on specific poses. With ControlNet, users can incorporate various poses into their AI Artworks. More features that were introduced into Artbreeder, are Pattern, which creates AI Pattern Images, Outpainting or Uncropping was also an added feature to Artbreeder, that allows the user to expand the image beyond the normal dimensions of the image. == Reception == The artwork generated by users of the website has been described as "beautiful" and "surreal," drawing comparisons to "weird, incomprehensible dreams" that "somehow touch the deep, unconscious parts of [the] mind". However, the generated faces were noted as "creepy and 'off'", and still nowhere near the quality attained by actual digital artists. Additionally, the site faced criticism for perceived confusing aspects of the AI's behavior. Jonathan Bartlett of Mind Matters News noted that "As is always the case with AI, sometimes the [gene] knobs don't work as expected and sometimes the results are... strange," while conceding that Artbreeder was still "probably the start of a new future of made-to-order stock images." Writers from Hyperallergic also took issue with perceived racial biases in the Portraits model, citing a comment from a user who faced difficulty from the neural network while attempting to darken the skin of a portrait to match a source image.

  Read more →
• 

  Autonomous aircraft

  An autonomous aircraft is an aircraft which flies under the control of on-board autonomous robotic systems and needs no intervention from a human pilot or remote control. Most contemporary autonomous aircraft are unmanned aerial vehicles (drones) with pre-programmed algorithms to perform designated tasks, but advancements in artificial intelligence technologies (e.g. machine learning) mean that autonomous control systems are reaching a point where several air taxis and associated regulatory regimes are being developed. == History == === Unmanned aerial vehicles === The earliest recorded use of an unmanned aerial vehicle for warfighting occurred in July 1849, serving as a balloon carrier (the precursor to the aircraft carrier) Significant development of radio-controlled drones started in the early 1900s, and originally focused on providing practice targets for training military personnel. The earliest attempt at a powered UAV was A. M. Low's "Aerial Target" in 1916. Autonomous features such as the autopilot and automated navigation were developed progressively through the twentieth century, although techniques such as terrain contour matching (TERCOM) were applied mainly to cruise missiles. Before the introduction of the Bayraktar Kızılelma some modern drones have a high degree of autonomy, although they were not fully capable and the regulatory environment prohibits their widespread use in civil aviation. However some limited trials had been undertaken. On December 17, 2025, two Bayraktar Kızılelma performed the world's first autonomous close-formation flight by two unmanned fighter jets, using artificial intelligence. This was the first time in the history of aviation when two unmanned aerial vehicles flew in close formation on their own. === Passengers === As flight, navigation and communications systems have become more sophisticated, safely carrying passengers has emerged as a practical possibility. Autopilot systems are relieving the human pilot of progressively more duties, but the pilot currently remains necessary. A number of air taxis are under development and larger autonomous transports are also being planned. The personal air vehicle is another class where from one to four passengers are not expected to be able to pilot the aircraft and autonomy is seen as necessary for widespread adoption. == Control system architecture == The computing capability of aircraft flight and navigation systems followed the advances of computing technology, beginning with analog controls and evolving into microcontrollers, then system-on-a-chip (SOC) and single-board computers (SBC). === Sensors === Position and movement sensors give information about the aircraft state. Exteroceptive sensors deal with external information like distance measurements, while proprioceptive ones correlate internal and external states. Degrees of freedom (DOF) refers to both the amount and quality of sensors on board: 6 DOF implies 3-axis gyroscopes and accelerometers (a typical inertial measurement unit – IMU), 9 DOF refers to an IMU plus a compass, 10 DOF adds a barometer and 11 DOF usually adds a GPS receiver. === Actuators === UAV actuators include digital electronic speed controllers (which control the RPM of the motors) linked to motors/engines and propellers, servomotors (for planes and helicopters mostly), weapons, payload actuators, LEDs and speakers. === Software === UAV software called the flight stack or autopilot. The purpose of the flight stack is to obtain data from sensors, control motors to ensure UAV stability, and facilitate ground control and mission planning communication. UAVs are real-time systems that require rapid response to changing sensor data. As a result, UAVs rely on single-board computers for their computational needs. Examples of such single-board computers include Raspberry Pis, Beagleboards, etc. shielded with NavIO, PXFMini, etc. or designed from scratch such as NuttX, preemptive-RT Linux, Xenomai, Orocos-Robot Operating System or DDS-ROS 2.0. Civil-use open-source stacks include: Due to the open-source nature of UAV software, they can be customized to fit specific applications. For example, researchers from the Technical University of Košice have replaced the default control algorithm of the PX4 autopilot. This flexibility and collaborative effort has led to a large number of different open-source stacks, some of which are forked from others, such as CleanFlight, which is forked from BaseFlight and from which three other stacks are forked from. === Loop principles === UAVs employ open-loop, closed-loop or hybrid control architectures. Open loop – This type provides a positive control signal (faster, slower, left, right, up, down) without incorporating feedback from sensor data. Closed loop – This type incorporates sensor feedback to adjust behavior (reduce speed to reflect tailwind, move to altitude 300 feet). The PID controller is common. Sometimes, feedforward is employed, transferring the need to close the loop further. == Communications == Most UAVs use a radio for remote control and exchange of video and other data. Early UAVs had only narrowband uplink. Downlinks came later. These bi-directional narrowband radio links carried command and control (C&C) and telemetry data about the status of aircraft systems to the remote operator. For very long range flights, military UAVs also use satellite receivers as part of satellite navigation systems. In cases when video transmission was required, the UAVs will implement a separate analog video radio link. In most modern autonomous applications, video transmission is required. A broadband link is used to carry all types of data on a single radio link. These broadband links can leverage quality of service techniques to optimize the C&C traffic for low latency. Usually, these broadband links carry TCP/IP traffic that can be routed over the Internet. Communications can be established with: Ground control – a military ground control station (GCS). The MAVLink protocol is increasingly becoming popular to carry command and control data between the ground control and the vehicle. Remote network system, such as satellite duplex data links for some military powers. Downstream digital video over mobile networks has also entered consumer markets, while direct UAV control uplink over the cellular mesh and LTE have been demonstrated and are in trials. Another aircraft, serving as a relay or mobile control station – military manned-unmanned teaming (MUM-T). As mobile networks have increased in performance and reliability over the years, drones have begun to use mobile networks for communication. Mobile networks can be used for drone tracking, remote piloting, over the air updates, and cloud computing. Modern networking standards have explicitly considered autonomous aircraft and therefore include optimizations. The 5G standard has mandated reduced user plane latency to 1ms while using ultra-reliable and low-latency communications. == Autonomy == Basic autonomy comes from proprioceptive sensors. Advanced autonomy calls for situational awareness, knowledge about the environment surrounding the aircraft from exteroceptive sensors: sensor fusion integrates information from multiple sensors. Civil aviation regulators and standards bodies have published high-level roadmaps and discussion papers focused on assurance, safety and governance of AI-enabled systems in aviation, particularly as autonomy increases in operations and decision support. === Basic principles === One way to achieve autonomous control employs multiple control-loop layers, as in hierarchical control systems. As of 2016 the low-layer loops (i.e. for flight control) tick as fast as 32,000 times per second, while higher-level loops may cycle once per second. The principle is to decompose the aircraft's behavior into manageable "chunks", or states, with known transitions. Hierarchical control system types range from simple scripts to finite state machines, behavior trees and hierarchical task planners. The most common control mechanism used in these layers is the PID controller which can be used to achieve hover for a quadcopter by using data from the IMU to calculate precise inputs for the electronic speed controllers and motors. Examples of mid-layer algorithms: Path planning: determining an optimal path for vehicle to follow while meeting mission objectives and constraints, such as obstacles or fuel requirements Trajectory generation (motion planning): determining control maneuvers to take in order to follow a given path or to go from one location to another Trajectory regulation: constraining a vehicle within some tolerance to a trajectory Evolved UAV hierarchical task planners use methods like state tree searches or genetic algorithms. === Autonomy features === UAV manufacturers often build in specific autonomous operations, such as: Self-level: attitude stabilization on the pitch and roll axes. Altitude hold: The aircraft maint

  Read more →
• 

  D/Vision Pro

  D/Vision Pro was one of the earliest marketed non-linear editing systems. It was released by TouchVision Systems, Inc. in the mid-1990s. The program was DOS-based and worked on either Intel's 386 or 486 processor. The system used AVI compression and worked with the Action Media II board. The system allowed users to digitize video, audio, and timecode, create an edit decision list (EDL), instantly play back the edited program, and output the finished EDL in a wide variety of formats. These cost-effective editing systems were used by numerous independent filmmakers and in low-budget productions during the mid-late 1990s. D/Vision Pro's low-quality compression led TouchVision (later renamed D/Vision Systems) to abandon it in favor of D/Vision Online, which was purchased by Discreet Logic and renamed edit. In June 2002, Discreet discontinued edit, as they did not want it to interfere with smoke sales which were more profitable. Discreet was later purchased by Autodesk.

  Read more →
• 

  Scale-space axioms

  In image processing and computer vision, a scale space framework can be used to represent an image as a family of gradually smoothed images. This framework is very general and a variety of scale space representations exist. A typical approach for choosing a particular type of scale space representation is to establish a set of scale-space axioms, describing basic properties of the desired scale-space representation and often chosen so as to make the representation useful in practical applications. Once established, the axioms narrow the possible scale-space representations to a smaller class, typically with only a few free parameters. A set of standard scale space axioms, discussed below, leads to the linear Gaussian scale-space, which is the most common type of scale space used in image processing and computer vision. == Scale space axioms for the linear scale-space representation == The linear scale space representation L ( x , y , t ) = ( T t f ) ( x , y ) = g ( x , y , t ) ∗ f ( x , y ) {\displaystyle L(x,y,t)=(T_{t}f)(x,y)=g(x,y,t)f(x,y)} of signal f ( x , y ) {\displaystyle f(x,y)} obtained by smoothing with the Gaussian kernel g ( x , y , t ) {\displaystyle g(x,y,t)} satisfies a number of properties 'scale-space axioms' that make it a special form of multi-scale representation: linearity T t ( a f + b h ) = a T t f + b T t h {\displaystyle T_{t}(af+bh)=aT_{t}f+bT_{t}h} where f {\displaystyle f} and h {\displaystyle h} are signals while a {\displaystyle a} and b {\displaystyle b} are constants, shift invariance T t S ( Δ x , Δ y ) f = S ( Δ x , Δ y ) T t f {\displaystyle T_{t}S_{(\Delta x,\Delta _{y})}f=S_{(\Delta x,\Delta _{y})}T_{t}f} where S ( Δ x , Δ y ) {\displaystyle S_{(\Delta x,\Delta _{y})}} denotes the shift (translation) operator ( S ( Δ x , Δ y ) f ) ( x , y ) = f ( x − Δ x , y − Δ y ) {\displaystyle (S_{(\Delta x,\Delta _{y})}f)(x,y)=f(x-\Delta x,y-\Delta y)} semi-group structure g ( x , y , t 1 ) ∗ g ( x , y , t 2 ) = g ( x , y , t 1 + t 2 ) {\displaystyle g(x,y,t_{1})g(x,y,t_{2})=g(x,y,t_{1}+t_{2})} with the associated cascade smoothing property L ( x , y , t 2 ) = g ( x , y , t 2 − t 1 ) ∗ L ( x , y , t 1 ) {\displaystyle L(x,y,t_{2})=g(x,y,t_{2}-t_{1})L(x,y,t_{1})} existence of an infinitesimal generator A {\displaystyle A} ∂ t L ( x , y , t ) = ( A L ) ( x , y , t ) {\displaystyle \partial _{t}L(x,y,t)=(AL)(x,y,t)} non-creation of local extrema (zero-crossings) in one dimension, non-enhancement of local extrema in any number of dimensions ∂ t L ( x , y , t ) ≤ 0 {\displaystyle \partial _{t}L(x,y,t)\leq 0} at spatial maxima and ∂ t L ( x , y , t ) ≥ 0 {\displaystyle \partial _{t}L(x,y,t)\geq 0} at spatial minima, rotational symmetry g ( x , y , t ) = h ( x 2 + y 2 , t ) {\displaystyle g(x,y,t)=h(x^{2}+y^{2},t)} for some function h {\displaystyle h} , scale invariance g ^ ( ω x , ω y , t ) = h ^ ( ω x φ ( t ) , ω x φ ( t ) ) {\displaystyle {\hat {g}}(\omega _{x},\omega _{y},t)={\hat {h}}({\frac {\omega _{x}}{\varphi (t)}},{\frac {\omega _{x}}{\varphi (t)}})} for some functions φ {\displaystyle \varphi } and h ^ {\displaystyle {\hat {h}}} where g ^ {\displaystyle {\hat {g}}} denotes the Fourier transform of g {\displaystyle g} , positivity g ( x , y , t ) ≥ 0 {\displaystyle g(x,y,t)\geq 0} , normalization ∫ x = − ∞ ∞ ∫ y = − ∞ ∞ g ( x , y , t ) d x d y = 1 {\displaystyle \int _{x=-\infty }^{\infty }\int _{y=-\infty }^{\infty }g(x,y,t)\,dx\,dy=1} . In fact, it can be shown that the Gaussian kernel is a unique choice given several different combinations of subsets of these scale-space axioms: most of the axioms (linearity, shift-invariance, semigroup) correspond to scaling being a semigroup of shift-invariant linear operator, which is satisfied by a number of families integral transforms, while "non-creation of local extrema" for one-dimensional signals or "non-enhancement of local extrema" for higher-dimensional signals are the crucial axioms which relate scale-spaces to smoothing (formally, parabolic partial differential equations), and hence select for the Gaussian. The Gaussian kernel is also separable in Cartesian coordinates, i.e. g ( x , y , t ) = g ( x , t ) g ( y , t ) {\displaystyle g(x,y,t)=g(x,t)\,g(y,t)} . Separability is, however, not counted as a scale-space axiom, since it is a coordinate dependent property related to issues of implementation. In addition, the requirement of separability in combination with rotational symmetry per se fixates the smoothing kernel to be a Gaussian. There exists a generalization of the Gaussian scale-space theory to more general affine and spatio-temporal scale-spaces. In addition to variabilities over scale, which original scale-space theory was designed to handle, this generalized scale-space theory also comprises other types of variabilities, including image deformations caused by viewing variations, approximated by local affine transformations, and relative motions between objects in the world and the observer, approximated by local Galilean transformations. In this theory, rotational symmetry is not imposed as a necessary scale-space axiom and is instead replaced by requirements of affine and/or Galilean covariance. The generalized scale-space theory leads to predictions about receptive field profiles in good qualitative agreement with receptive field profiles measured by cell recordings in biological vision. In the computer vision, image processing and signal processing literature there are many other multi-scale approaches, using wavelets and a variety of other kernels, that do not exploit or require the same requirements as scale space descriptions do; please see the article on related multi-scale approaches. There has also been work on discrete scale-space concepts that carry the scale-space properties over to the discrete domain; see the article on scale space implementation for examples and references.

  Read more →
• 

  Computer appliance

  A computer appliance is a computer system with a combination of hardware, software, or firmware that is specifically designed to provide a particular computing resource. Such devices became known as appliances because of the similarity in role or management to a home appliance, which are generally closed and sealed, and are not serviceable by the user or owner. The hardware and software are delivered as an integrated product and may even be pre-configured before delivery to a customer, to provide a turn-key solution for a particular application. Unlike general purpose computers, appliances are generally not designed to allow the customers to change the software and the underlying operating system, or to flexibly reconfigure the hardware. Another form of appliance is the virtual appliance, which has similar functionality to a dedicated hardware appliance, but is distributed as a software virtual machine image for a hypervisor-equipped device. == Overview == Traditionally, software applications run on top of a general-purpose operating system, which uses the hardware resources of the computer (primarily memory, disk storage, processing power, and networking bandwidth) to meet the computing needs of the user. The main issue with the traditional model is related to complexity. It is complex to integrate the operating system and applications with a hardware platform, and complex to support it afterwards. By tightly constraining the variations of the hardware and software, the appliance becomes easily deployable, and can be used without nearly as wide (or deep) IT knowledge. Additionally, when problems and errors appear, the supporting staff very rarely needs to explore them deeply to understand the matter thoroughly. The staff needs merely training on the appliance management software to be able to resolve most of problems. In all forms of the computer appliance model, customers benefit from easy operations. The appliance has exactly one combination of hardware and operating system and application software, which has been pre-installed at the factory. This prevents customers from needing to perform complex integration work, and dramatically simplifies troubleshooting. In fact, this "turnkey operation" characteristic is the driving benefit that customers seek when purchasing appliances. To be considered an appliance, the (hardware) device needs to be integrated with software, and both are supplied as a package. This distinguishes appliances from "home grown" solutions, or solutions requiring complex implementations by integrators or value-added resellers (VARs). The appliance approach helps to decouple the various systems and applications, for example in the data center. Once a resource is decoupled, in theory it can be also centralized to become shared among many systems, centrally managed and optimized, all without requiring changes to any other system. == Tradeoffs of the computer appliance approach == The major disadvantage of deploying a computer appliance is that since they are designed to supply a specific resource, they most often include a customized operating system running over specialized hardware, neither of which are likely to be compatible with the other systems previously deployed. Customers lose flexibility. One may believe that a proprietary embedded operating system, or operating system within an application, can make the appliance much more secure from common cyber attacks. However, the opposite is true. Security by obscurity is a poor security decision, and appliances are often plagued by security issues as evidenced by the proliferation of IoT devices. == Types of appliances == The variety of computer appliances reflects the wide range of computing resources they provide to applications. Some examples: Storage appliances provide large amounts of storage, often available to many machines on the network. See Network-attached storage and Storage area network. Network appliances are general purpose routers which may also provide firewall protection, Transport Layer Security (TLS), messaging, access to specialized networking protocols (like the ebXML Message Service) and bandwidth multiplexing for the multiple systems they front-end. Backup and disaster recovery appliances computer appliances that are integrated backup software and backup targets, sometimes with hypervisors to support local DR of protected servers. They are often a gateway to a full DRaaS solution. Firewall and Security appliances Dedicated network appliances that are designed to protect computer networks from unwanted traffic. IIoT and MES Gateway appliances Computer appliances that are designed to translate data bidirectionally between control systems and enterprise systems. Proprietary, embedded, firmware applications running on the appliance use point-to-point connections to translate data between field devices in their native automation protocols and MES systems through their APIs, ODBC, or RESTful interfaces. Anti-spam appliances for e-mail spam Software appliances A single application server appliance, with just enough operating system (JeOS) for it to run. Virtual machine appliances consist of a "hypervisor style" embedded operating system running on appliance hardware. The hypervisor layer is matched to the hardware of the appliance, and cannot be varied by the customer, but the customer may load other operating systems and applications onto the appliance in the form of virtual machines. == Consumer appliances == Aside from its deployment within data centers, many computer appliances are directly used by the general public. These include: Digital video recorder Residential gateway Network-attached storage (NAS) Video game console Consumer uses stress the need for an appliance to have easy installation, configuration, and operation, with little or no technical knowledge being necessary. == Appliances in industrial automation == The world of industrial automation has been rich in appliances. These appliances have been hardened to withstand temperature and vibration extremes. These appliances are also highly configurable, enabling customization to meet a wide variety of applications. The key benefits of an appliance in automation are: Reduced downtime - a failed appliance is typically replaced with a COTS replacement and its task is quickly and easily reloaded from a backup. Highly scalable - appliances are typically targeted solutions for an area of a plant or process. As the requirements change, scalability is achieved through the installation of another appliance. Automation concepts are easily replicated throughout the enterprise by standardizing on appliances to perform the needed tasks, as opposed to the development of custom automation schemes for each task. Low TCO (total cost of ownership) - appliances are developed, tested and supported by automation product vendors and undergo a much broader level of quality testing than custom designed automation solutions. The use of appliances in automation reduce the level of testing needed in each individual application. Reduced design time - appliances perform specific functions and although they are highly configurable, they are typically self documenting. This enables appliance based solutions to be transferred from engineer to engineer with minimal need for training and documentation. Types of automation appliances: PLC (programmable logic controller) - Programmable logic controllers are appliances that are typically used for discrete control and offer a wide range of Input and Output options. They are configured through standardized programming languages such as IEC-1131. PID (proportional–integral–derivative controller) - PID controllers are appliances that monitor a process variable and, based on an error term, effect change on a control output (manipulated variable) to drive the process variable to a setpoint. PAC (programmable automation controller) - Programmable automation controllers are appliances that embody properties of both PLCs and PID controllers enabling the integration of both analog and discrete control. Universal gateway - A universal gateway appliance has the ability to communicate with a variety of devices through their respective communication protocols, and will affect data transactions between them. This in increasingly important as manufacturing strives to improve agility, quality, production rates, production costs and reduce downtime through enhanced M2M (machine to machine) communications. EATMs (Enterprise Appliance Transaction Modules) - Enterprise appliance transaction modules are appliances that affect data transactions from plant floor automation systems to enterprise business systems. They communicate to plant floor equipment through various vendor automation protocols, and communicate to business systems through database communication protocols such as JMS (Java Message Service) and SQL (Structured Query Language). == Internal structure == There are several

  Read more →
• 

  DAVI

  The Dutch Automated Vehicle Initiative (DAVI) is a research and demonstration initiative developing automated vehicles for use on public roads. The project is unique in that, besides simply making driverless cars, it also focuses on having automated vehicles share information among each other. The aim is to have the cars help to avoid traffic congestion by reducing the safety distance between the cars (from 2 seconds to 0.5 seconds) and avoiding sudden traffic slow-downs due to maneuvers undertaken by drivers.

  Read more →
• 

  BigDog

  BigDog is a dynamically stable quadruped military robot platform that was created in 2005 by Boston Dynamics with the Harvard University Concord Field Station. It was funded by the U.S. Defense Advanced Research Projects Agency (DARPA), but the project was shelved after the BigDog's gas engine was deemed too loud for combat. == History == BigDog was funded by the Defense Advanced Research Projects Agency (DARPA) in the hopes that it would be able to serve as a mechanic pack mule to accompany soldiers in terrain too rough for conventional vehicles. Instead of wheels or treads, BigDog uses four legs for movement, allowing it to move across surfaces that would be difficult for wheels. The legs contain a variety of sensors, including joint position and ground contact. BigDog also features a laser gyroscope and a stereo vision system. BigDog is 3 feet (0.91 m) long, stands 2.5 feet (0.76 m) tall, and weighs 240 pounds (110 kg), making it about the size of a small mule. It is capable of traversing difficult terrain, running at four miles per hour (6.4 km/h), carrying 340 pounds (150 kg), and climbing a 35 degree incline. Locomotion is controlled by an onboard computer that receives input from the robot's various sensors. Navigation and balance are also managed by the control system. BigDog's walking pattern is controlled through four legs, each equipped with four low-friction hydraulic cylinder actuators that power the joints. BigDog's locomotion behaviors can vary greatly. It can stand up, sit down, walk with a crawling gait that lifts one leg at a time, walk with a trotting gait lifting diagonal legs, or trot with a running gait. The travel speed of BigDog varies from a 0.62 mph (1 km/h) crawl to a 3.3 mph (5.3 km/h) trot. The BigDog project was headed by Dr. Martin Buehler, who received the Joseph Engelberger Award from the Robotics Industries Association in 2012 for the work. Dr. Buehler while previously a professor at McGill University, headed the robotics lab there, developing four-legged walking and running robots. Built onto the actuators are sensors for joint position and force, and movement is ultimately controlled through an onboard computer which manages the sensors. Approximately 50 sensors are located on BigDog. These measure the attitude and acceleration of the body, motion, and force of joint actuators as well as engine speed, temperature and hydraulic pressure inside the robot's internal engine. Low-level control, such as position and force of the joints, and high-level control such as velocity and altitude during locomotion, are both controlled through the onboard computer. BigDog was featured in episodes of Web Junk 20 and Hungry Beast, and in articles in New Scientist, Popular Science, Popular Mechanics, and The Wall Street Journal. In September 2011 Boston Dynamics released video footage of a new generation of BigDog known as AlphaDog. The footage shows AlphaDog's ability to walk on rough terrain and recover its balance when kicked from the side. The refined equivalent has been designed by Boston Dynamics to exceed the BigDog in terms of capabilities and use to dismounted soldiers. In February 2012, with further DARPA support, the militarized Legged Squad Support System (LS3) variant of BigDog demonstrated its capabilities during a hike over a rough terrain. Starting in the summer of 2012, DARPA planned to complete the overall development of the system and refine its key capabilities in 18 months, ensuring its worth to dismounted warfighters before it is rolled out to squads operating in-theatre. BigDog must be able to demonstrate its ability to complete a 20-mile (32 km) trail in 24 hours, without refuelling, while carrying a 325-pound (150 kg) load. A refinement of its vision sensors will also be conducted. At the end of February 2013, Boston Dynamics released video footage of a modified BigDog with an arm. The arm could pick up objects and throw them. The robot is relying on its legs and torso to help power the motions of the arm. It is believed that it can lift weights around 55 pounds (25 kg). This work was funded by the United States Army Research Laboratory and paved the way for integrating manipulators with quadrupeds as found on Spot, the spiritual successor of BigDog. === Discontinuation === At the end of December 2013, the BigDog project was discontinued. Despite hopes that it would one day work like a pack mule for US soldiers in the field, the gasoline-powered engine was deemed too noisy for use in combat, and it could be heard from hundreds of meters away. A similar project for an all-electric robot named Spot in 2016 was much quieter, but could only carry 45 pounds (20 kg). Both projects are no longer in progress, but the Spot was only released in 2020. == Hardware == BigDog is powered by a small two-stroke, one-cylinder, 15-brake-horsepower (11 kW) engine operating at 9,000 RPM. The engine drives a hydraulic pump, which in turn drives the hydraulic leg actuators. Each leg has four actuators (two for the hip joint, and two each for the knee and ankle joints), for a total of 16. Each actuator unit consists of a hydraulic cylinder, servo valve, position sensor, and force sensor. Onboard computing power is a ruggedized PC/104 board stack with two computers, one running a Pentium M processor running QNX (used for sensor data processing) and another running a Core Duo processor (used for visual data processing). == Gallery ==

  Read more →
• 

  Predictive text

  Predictive text is an input technology used where one key or button represents many letters, such as on the physical numeric keypads of mobile phones and in accessibility technologies. Each key press results in a prediction rather than repeatedly sequencing through the same group of "letters" it represents, in the same, invariable order. Predictive text could allow for an entire word to be input by a single keypress. Predictive text makes efficient use of fewer device keys to input writing into a text message, an e-mail, an address book, a calendar, and the like. The most widely used, general, predictive text systems are T9, iTap, eZiText, and LetterWise/WordWise. There are many ways to build a device that predicts text, but all predictive text systems have initial linguistic settings that offer predictions that are re-prioritized to adapt to each user. This learning adapts, by way of the device memory, to a user's disambiguating feedback that results in corrective key presses, such as pressing a "next" key to get to the intention. Most predictive text systems have a user database to facilitate this process. Theoretically the number of keystrokes required per desired character in the finished writing is, on average, comparable to using a keyboard. This is approximately true provided that all words used are in its database, punctuation is ignored, and no input mistakes are made when typing or spelling. The theoretical keystrokes per character, KSPC, of a keyboard is KSPC=1.00, and of multi-tap is KSPC=2.03. Eatoni's LetterWise is a predictive multi-tap hybrid, which when operating on a standard telephone keypad achieves KSPC=1.15 for English. The choice of which predictive text system is the best to use involves matching the user's preferred interface style, the user's level of learned ability to operate predictive text software, and the user's efficiency goal. There are various levels of risk in predictive text systems, versus multi-tap systems, because the predicted text that is automatically written provides the speed and mechanical efficiency benefit, which, if the user is not careful to review, results in transmitting misinformation. Predictive text systems take time to learn to use well, and so generally, a device's system has user options to set up the choice of multi-tap or any one of several schools of predictive text methods. == Background == Short message service (SMS) permits a mobile phone user to send text messages (also called messages, SMSes, texts, and txts) as a short message. The most common system of SMS text input is referred to as "multi-tap". Using multi-tap, a key is pressed multiple times to access the list of letters on that key. For instance, pressing the "2" key once displays an "a", twice displays a "b" and three times displays a "c". To enter two successive letters that are on the same key, the user must either pause or hit a "next" button. A user can type by pressing an alphanumeric keypad without looking at the electronic equipment display. Thus, multi-tap is easy to understand and can be used without any visual feedback. However, multi-tap is not very efficient, requiring potentially many keystrokes to enter a single letter. In ideal predictive text entry, all words used are in the dictionary, punctuation is ignored, no spelling mistakes are made, and no typing mistakes are made. The ideal dictionary would include all slang, proper nouns, abbreviations, URLs, foreign-language words and other user-unique words. This ideal circumstance gives predictive text software a reduction in the number of key strokes a user is required to enter a word. The user presses the number corresponding to each letter. As long as the word exists in the predictive text dictionary or is correctly disambiguated by non-dictionary systems, it will appear. For instance, pressing "4663" will typically be interpreted as the word good, provided that a linguistic database in English is currently in use, though alternatives such as home, hood and hoof are also valid interpretations of the sequence of key strokes. The most widely used systems of predictive text are Tegic's T9, Motorola's iTap, and the Eatoni Ergonomics' LetterWise and WordWise. T9 and iTap use dictionaries, but Eatoni Ergonomics' products use a disambiguation process, a set of statistical rules to recreate words from keystroke sequences. All predictive text systems require a linguistic database for every supported input language. == Dictionary vs. non-dictionary systems == Traditional disambiguation works by referencing a dictionary of commonly used words, though Eatoni offers a dictionaryless disambiguation system. In dictionary-based systems, as the user presses the number buttons, an algorithm searches the dictionary for a list of possible words that match the keypress combination and offers up the most probable choice. The user can then confirm the selection and move on, or use a key to cycle through the possible combinations. A non-dictionary system constructs words and other sequences of letters from the statistics of word parts. To attempt predictions of the intended result of keystrokes not yet entered, disambiguation may be combined with a word completion facility. Either system (disambiguation or predictive) may include a user database, which can be further classified as a "learning" system when words or phrases are entered into the user database without direct user intervention. The user database is for storing words or phrases that are not well disambiguated by the pre-supplied database. Some disambiguation systems further attempt to correct spelling, format text or perform other automatic rewrites, with the risky effect of either enhancing or frustrating user efforts to enter text. == History == The predictive text and autocomplete technology was invented out of necessities by Chinese scientists and linguists in the 1950s to solve the input inefficiency of the Chinese typewriter, as the typing process involved finding and selecting thousands of logographic characters on a tray, drastically slowing down the word processing speed. The actuating keys of the Chinese typewriter created by Lin Yutang in the 1940s included suggestions for the characters following the one selected. In 1951, the Chinese typesetter Zhang Jiying arranged Chinese characters in associative clusters, a precursor of modern predictive text entry, and broke speed records by doing so. Predictive entry of text from a telephone keypad has been known at least since the 1970s (Smith and Goodwin, 1971). Predictive text was mainly used to look up names in directories over the phone until mobile phone text messaging came into widespread use. == Example == On a typical phone keypad, if users wished to type the in a "multi-tap" keypad entry system, they would need to: Press 8 (tuv) once to select t. Press 4 (ghi) twice to select h. Press 3 (def) twice to select e. Meanwhile, in a phone with predictive text, they need only: Press 8 once to select the (tuv) group for the first character. Press 4 once to select the (ghi) group for the second character. Press 3 once to select the (def) group for the third character. The system updates the display as each keypress is entered, to show the most probable entry. In this example, prediction reduced the number of button presses from five to three. The effect is even greater with longer words and those composed of letters later in each key's sequence. A dictionary-based predictive system is based on the hope that the desired word is in the dictionary. That hope may be misplaced if the word differs in any way from common usage—in particular, if the word is not spelled or typed correctly, is slang, or is a proper noun. In these cases, some other mechanism must be used to enter the word. Furthermore, the simple dictionary approach fails with agglutinative languages, where a single word does not necessarily represent a single semantic entity. == Companies and products == Predictive text is developed and marketed in a variety of competing products, such as Nuance Communications's T9. Other products include Motorola's iTap; Eatoni Ergonomic's LetterWise (character, rather than word-based prediction); WordWise (word-based prediction without a dictionary); EQ3 (a QWERTY-like layout compatible with regular telephone keypads); Prevalent Devices's Phraze-It; Xrgomics' TenGO (a six-key reduced QWERTY keyboard system); Adaptxt (considers language, context, grammar and semantics); Lightkey (a predictive typing software for Windows); Clevertexting (statistical nature of the language, dictionaryless, dynamic key allocation); and Oizea Type (temporal ambiguity); Intelab's Tauto; WordLogic's Intelligent Input Platform™ (patented, layer-based advanced text prediction, includes multi-language dictionary, spell-check, built-in Web search); Google's Gboard. == Textonyms == Words produced by the same combination of keypresses have been called "textonyms"; also "txtonyms"; or "T9o

  Read more →
• 

  D/Vision Pro

  D/Vision Pro was one of the earliest marketed non-linear editing systems. It was released by TouchVision Systems, Inc. in the mid-1990s. The program was DOS-based and worked on either Intel's 386 or 486 processor. The system used AVI compression and worked with the Action Media II board. The system allowed users to digitize video, audio, and timecode, create an edit decision list (EDL), instantly play back the edited program, and output the finished EDL in a wide variety of formats. These cost-effective editing systems were used by numerous independent filmmakers and in low-budget productions during the mid-late 1990s. D/Vision Pro's low-quality compression led TouchVision (later renamed D/Vision Systems) to abandon it in favor of D/Vision Online, which was purchased by Discreet Logic and renamed edit. In June 2002, Discreet discontinued edit, as they did not want it to interfere with smoke sales which were more profitable. Discreet was later purchased by Autodesk.

  Read more →
• 

  Graphics software

  In computer graphics, graphics software refers to a program or collection of programs that enable a person to manipulate images or models visually on a computer. Computer graphics can be classified into two distinct categories: raster graphics and vector graphics, with further 2D and 3D variants. Many graphics programs focus exclusively on either vector or raster graphics, but there are a few that operate on both. It is simple to convert from vector graphics to raster graphics, but going the other way is harder. Some software attempts to do this. In addition to static graphics, there are animation and video editing software. Different types of software are often designed to edit different types of graphics such as video, photos, and vector-based drawings. The exact sources of graphics may vary for different tasks, but most can read and write files. Most graphics programs have the ability to import and export one or more graphics file formats, including those formats written for a particular computer graphics program. Such programs include, but are not limited to: GIMP, Adobe Photoshop, CorelDRAW, Microsoft Publisher, Picasa, etc. The use of a swatch is a palette of active colours that are selected and rearranged by the preference of the user. A swatch may be used in a program or be part of the universal palette on an operating system. It is used to change the colour of a text or image and in video editing. Vector graphics animation can be described as a series of mathematical transformations that are applied in sequence to one or more shapes in a scene. Raster graphics animation works in a similar fashion to film-based animation, where a series of still images produces the illusion of continuous movement. == History == SuperPaint was one of the earliest graphics software applications, first conceptualized in 1972 and achieving its first stable image in 1973 Fauve Matisse (later Macromedia xRes) was a pioneering program of the early 1990s, notably introducing layers in customer software. Currently Adobe Photoshop is one of the most used and best-known graphics programs in the Americas, having created more custom hardware solutions in the early 1990s, but was initially subject to various litigation. GIMP is a popular open-source alternative to Adobe Photoshop.

  Read more →
• 

  VGACAD

  VGACAD was the parent of a suite of shareware graphic utilities made for the MS-DOS operating system used in the IBM PC and clones. It was popular for editing and capturing images using BSAVE (graphics image format) and provided an early graphic editing suite compatible with multiple graphic cards and resolutions, used on the IBM PC. == Usage == Written by Lawrence Gozum in 1987, it was the genesis of multiple versions and improvements over 10 years. Ran with his brother, Marvin initially helped with design ideas, strategic focus, technical support calls, and managing the early shareware business. The growth of the VGACAD suite grew quickly to preoccupy most of their time. Lawrence then focused more of his efforts on software and formed Applied Insights, to manage VGACAD and its offspring, VidFun, and Ai Picture Explorer. At its peak, its users ranged from individuals, Federal government offices, museums and major newspapers. == Features == VGACAD was a misnomer, and meant VGA-Computer Assisted Drawing, rather than computer-aided design, as CAD is commonly referred to today. Its longevity was due to its color accuracy, speed, small size, and that its suite of small utilities often worked stand-alone. One called VGACAP, for 'capture', dumped video memory into a file that could later be converted to popular graphic image formats, later made commonplace when Microsoft Windows programmed the print screen key to dump graphics into the clipboard. However, VGACAP ran insulated apart from early versions of Windows, and thus could capture screens were applications prohibited such function.

  Read more →
• 

  List of Fortran software and tools

  This is a list of Fortran software and tools, including IDEs, compilers, libraries, debugging tools, numerical and scientific computing tools, and related projects. == Fortran compilers == Absoft Pro Fortran — Absoft Pro Fortran is discontinued and ran on Linux and macOS AOCC — from AMD Classic Flang — part of the LLVM Project LLVM Flang — part of the LLVM Project Fortran 77 — Fortran 77 was developed by Digital Equipment Corporation, it is discontinued. G95 – portable open-source Fortran 95 compiler GCC (GNU Fortran) PGI compilers – NVIDIA developed compilers after acquiring The Portland Group IBM XL Fortran — IBM XL Fortran is current and runs on Linux (Power/AIX) and integrates with Eclipse Intel Fortran Compiler – part of Intel OneAPI HPC toolkit LFortran — LFortran is current, cross-platform, and has IDE support. MinGW – cross compiler and forked into Mingw-w64 nAG Fortran Compiler - from nAG Open64 — Open64 is an open-source compiler that has been terminated and ran on Linux Open Watcom — Open Watcom is current, runs on MS-DOS and OS/2, and has IDE support. Oracle Fortran — Oracle Fortran is discontinued, ran on Linux and Solaris. ROSE — source-to-source compiler framework developed at Lawrence Livermore National Laboratory Silverfrost FTN95 — FTN95 from Silverfrost is current, runs on Windows, and has IDE support. == Integrated development environments (IDEs) and editors == Code::Blocks — supports Fortran with plugins Eclipse IDE — with Fortran support via Photran Emacs — extensible text editor with built-in Fortran modes and support for modern tooling via language servers Geany — lightweight cross-platform IDE based on GTK IntelliJ IDEA — cross-platform IDE by JetBrains with Fortran pluggin KDevelop — KDE-based IDE NetBeans — Apache software foundation IDE with Fortran configuration OpenWatcom — IDE and compiler suite for C, C++, and Fortran Simply Fortran — standalone Fortran IDE for Windows, Linux, and macOS Vim — modal text editor with native Fortran syntax support and extensive plugin-based development features Visual Studio — with Intel Fortran integration Visual Studio Code — supports Fortran via extensions == Mathematical libraries == == Scientific libraries == ABINIT — software suite to calculate optical, mechanical, vibrational, and other observable properties of materials Cantera — chemical kinetics, thermodynamics, and transport tool suite CERN Program Library — collection of Fortran libraries for physics applications from CERN CP2K — quantum chemistry and solid-state physics software package for atomistic simulations Dalton — molecular electronic structure program FFTPACK — subroutines for the fast Fourier transform Kinetic PreProcessor – open-source software tool used in atmospheric chemistry MESA — Modules for Experiments in Stellar Astrophysics Nek5000 — MPI parallel higher-order spectral element CFD solver NWChem — open-source high-performance computational chemistry software Octopus — real-space Time-Dependent Density Functional Theory code MODTRAN – model atmospheric propagation of electromagnetic radiation MOLCAS — quantum chemistry software package for multiconfigurational electronic structure calculations NOVAS – software library for astrometry-related numerical computations Physics Analysis Workstation – data analysis and graphical presentation in high-energy physics Quantum ESPRESSO — integrated suite for electronic-structure calculations and materials modeling SIESTA — first-principles materials simulation code using density functional theory Tinker — software tools for molecular design == Debugging and performance tools == GDB — GNU Debugger with Fortran support Valgrind — memory debugging and profiling tool VTune Profiler — performance analysis tool Allinea Forge — debugger and profiler for HPC applications == Build and package management == Autotools — build system supporting Fortran projects CMake — cross-platform build system supporting Fortran Make — build automation tool Spack — package manager for HPC software including Fortran libraries == Machine learning and AI libraries == Athena Fiats (Functional Inference And Training for Surrogates) FNN (Fortran Neural Network) FortNN Fortran-TF-lib (Fortran interface to TensorFlow) FTorch (Fortran interface to PyTorch) MlFortran RoseNNa == Parallel and high-performance computing tools == MPI Fortran bindings — standard interface for distributed-memory parallelism OpenMP — shared-memory parallel programming support through compiler directives Coarray Fortran — parallel programming model introduced in Fortran 2008 ScaLAPACK — parallel linear algebra package built on top of LAPACK == Testing frameworks == FUnit — open-source unit testing framework developed at NASA’s Langley Research Center, for Fortran 90, 95, and 2003. pFUnit — unit testing framework for Fortran, modeled after JUnit == Documentation and code analysis tools == FORD — automatic documentation generator for modern Fortran projects SQuORE — software quality and management platform with code analysis support Understand — static analysis and code comprehension tool for large Fortran projects

  Read more →
• 

  MoltenVK

  MoltenVK is a software library which allows Vulkan applications to run on top of Metal on Apple's macOS, iOS, and tvOS operating systems. It is the first software component to be released for the Vulkan Portability Initiative, a project to have a subset of Vulkan run on platforms lacking native Vulkan drivers. There are some limitations compared with a native Vulkan implementation. == History == MoltenVK was first released as a proprietary and commercially licensed product by The Brenwill Workshop on July 27, 2016. On July 31, 2017, Khronos announced the formation of the Vulkan Portability Technical Subgroup. === Open source === On February 26, 2018, Khronos announced that Vulkan became available on macOS and iOS products through the MoltenVK library. Valve announced that Dota 2 will run on macOS using the Vulkan API with the aid of MoltenVK, and that they had made an arrangement with developer The Brenwill Workshop Ltd to release MoltenVK as open-source software under the Apache License version 2.0. On May 30, 2018, Qt was updated with Vulkan for Qt on macOS using MoltenVK. On May 31, 2018, optional Vulkan support for Dota 2 on macOS was released. Benchmarks for the game were available the following day, showing better performance using Vulkan and MoltenVK compared to OpenGL. On July 20, 2018, Wine was updated with Vulkan support on macOS using MoltenVK. On 29 July 2018, the first app using MoltenVK was accepted onto the App Store, after initially being rejected. On 6 August 2018, Google open-sourced Filament, a crossplatform real-time physically based rendering engine with MoltenVK for macOS/iOS. On November 28, 2018, Valve released Artifact, their first Vulkan-only game on macOS using MoltenVK. === Version 1.0 === On 29 January 2019, MoltenVK 1.0.32 was released with early prototype of Vulkan Portability Extensions. RPCS3 and Dolphin emulators were updated with Vulkan support on macOS using MoltenVK. On 13 April 2019, MoltenVK 1.0.34 was released with support for tessellation. On July 30, 2019, MoltenVK 1.0.36 was released targeting Metal 3.0. On July 31, 2020, MoltenVK 1.0.44 was released, adding support for the tvOS platform. On January 23, 2020, MoltenVK was updated to support for some of the new features of Vulkan 1.2, as of Vulkan SDK 1.2.121. === Version 1.1 === On October 1, 2020, MoltenVK 1.1.0 was released, adding full support for Vulkan 1.1, as of Vulkan SDK 1.2.154. On 9 December 2020, MoltenVK 1.1.1 was released, providing support for Vulkan on Apple silicon GPUs and support for the Mac Catalyst platform for porting iOS/iPadOS apps to macOS. === Version 1.2 === On October 18, 2022, MoltenVK 1.2.0 was released, adding full support for Vulkan 1.2 as of Vulkan SDK 1.3.231. In January 2023, MoltenVK 1.2.2 added support for Vulkan as of SDK 1.3.239, while this version of Vulkan SDK fixed some issues with the interconnectivity with Metal API, while version 1.2.3 supported some additional extensions. === Version 1.3 === On May 1, 2025, MoltenVK 1.3 was released with support for Vulkan 1.3. === Version 1.4 === On August 20, 2025, MoltenVK 1.4 was released with support for Vulkan 1.4.

  Read more →
• 

  Boris FX

  Boris FX is a visual effects, video editing, photography, and audio software plug-in developer based in Miami, Florida, USA. The developer is known for its flagship products, Continuum (formerly Boris Continuum Complete/BCC), Sapphire, Mocha, and Silhouette. Boris FX creates plug-in tools for feature film, broadcast television, and multimedia post-production workflows. The plug-ins are compatible with various NLEs, including Adobe After Effects and Premiere Pro, Avid Media Composer, Apple Final Cut Pro, and OFX hosts such as Autodesk Flame, Foundry Nuke, Blackmagic Design DaVinci Resolve and Fusion, and VEGAS Pro. Boris FX has incorporated artificial intelligence into its software, introducing features for noise reduction, rotoscoping, upscaling, and masking. The company has acquired technologies via mergers and acquisitions from Imagineer Systems, GenArts, Silhouette FX, Digital Film Tools, CrumplePop and Andersson Technologies to expand its visual effects, editing, photography, and audio tools. == History == Boris FX was founded in 1995 by Boris Yamnitsky. The former Media 100 engineer (a member of the original Media 100 launch team in 1993) released “Boris FX,” the first plug-in-based digital video effects (DVE) for Adobe Premiere and Media 100, in 1995. The plug-in won Best of Show at Apple Macworld in Boston, MA that same year. The Boris FX Suite includes a range of visual effects and post-production tools, such as Sapphire, Continuum, Mocha Pro, Silhouette, SynthEyes, CrumplePop, Optics, and Particle Illusion. == Media 100 == In October 2005, Yamnitsky acquired Media 100 the company that launched his plug-in career. Boris FX had a long relationship with Media 100 which bundled Boris RED software as its main titling and compositing solution. Media 100's video editing software is available as freeware for macOS. == Continuum == Continuum is a visual effect and compositing plugin suite that includes a library of over 300 effects and more than 40 transitions, including tools for image restoration, compositing, titling, particle generation, and stylized effects, along with features such as lens flares, lighting effects, and cinematic color grading presets. A key component of Continuum is its integration with the Mocha planar tracking and masking system, enabling advanced tracking and rotoscoping within the effects. The suite also includes Particle Illusion, a real-time particle generator used for creating visual effects such as explosions, smoke, and abstract motion graphics, as well as Primatte Studio, a chroma keying and compositing toolset for green screen and blue screen workflows. Continuum supports GPU acceleration and offers compatibility with HDR and 360/VR content. Regular updates introduce new effects, presets, and performance enhancements to expand its capabilities. In October 2018, Continuum relaunched Particle Illusion, a Mocha Essentials workflow with magnetic edge-snapping, and updates to Title Studio. In October 2019, Continuum introduced Corner Pin Studio with built-in Mocha tracking for quick screen replacement and inserts, 6 stylized transitions, and 4 creative effects. In October 2020, Continuum released an update that included over 80 GPU-accelerated effects such as film stocks, color grades, optical filter simulations, and a digital gobo library. The update also introduced a custom FX Editor interface, real-time particles, and more than 1,000 drag-and-drop presets. In November 2021, it added multi-frame rendering for After Effects, native Apple M1 support, fluid dynamics in Particle Illusion, and 60 color-grade presets. In October 2022, the software introduced 10 additional transitions, a revised Particle Illusion workflow, an atmospheric glow effect, and more than 250 curated presets. Continuum plugins have been used in television, streaming, and film projects, including A Black Lady Sketch Show (HBO/HBO Max), Star Trek: Discovery (CBS), Andor (Disney+), The Curse of Oak Island (History Channel), Keeping up with the Kardashians (E!), This Old House (PBS), Ms. Marvel (Disney+), MasterChef (Fox), WipeOut (TBS), The Boys (Prime Video), and The Today Show (NBC). == Mocha Pro == In December 2014, Boris FX merged with Imagineer Systems, the UK-based developer of the Academy Award-winning planar motion tracking software, Mocha Pro. Mocha Pro's features include planar tracking (motion tracking), rotoscoping, image stabilization, 3D camera tracking, and object removal. In June 2016, Mocha released (v5) which introduced Mocha Pro's tools as plug-ins for Adobe After Effects and Premiere Pro, Avid Media Composer, and OFX hosts Foundry's NUKE, Blackmagic Design Fusion, VEGAS Pro, and HitFilm. A simplified version, Mocha AE, is included with Adobe After Effects Creative Cloud and has been bundled with the software since CS4. A similar version is also available with HitFilm Pro from FXhome and VEGAS Pro. Mocha's tracking SDK is integrated into other visual effects tools, including SAM Quantel Pablo Rio, Silhouette FX, CoreMelt, and Motion VFX. Mocha Pro has been used in various film and television productions, including Birdman, Black Swan, the Harry Potter series, The Hobbit, Star Wars, The Mandalorian, Star Trek: Discovery, and The Umbrella Academy. It has also been employed in projects such as Gone Girl, The Hunger Games: Mockingjay – Part 1, Game of Thrones, and House of Cards. == Sapphire == GenArts, founded by Karl Sims in 1996, developed visual effects plug-ins that were used by studios and post-production facilities. In September 2016, Boris FX merged with former competitor, GenArts, Inc., developer of Sapphire high-end visual effects plug-ins, to expand its suite of motion graphics and VFX tools. The merger brought Sapphire alongside Boris Continuum Complete (BCC) and Mocha Pro, integrating these tools for film and television post-production. The Sapphire suite includes a library of over 270 effects and transitions, organized into categories such as lighting, stylization, distortions, textures, and transitions. Commonly used effects include glows, lens flares, film looks, and blurs. The plug-ins are designed to be GPU-accelerated, allowing for improved rendering performance and real-time previews in supported host applications. A central feature of Sapphire is the Builder tool, a node-based workspace that allows users to create custom effects and transitions by combining multiple Sapphire plug-ins. This enables a high level of creative flexibility and reusability, making it a popular tool for both editors and VFX artists. Sapphire also integrates with Mocha, Boris FX's planar tracking and masking system, allowing for advanced control of visual elements within an effect. In October 2017, Boris FX released its first new version of Sapphire since the GenArts acquisition. Sapphire (v11) now includes integrated Mocha tracking and masking tools. Sapphire is available for Adobe, Avid, the Autodesk Flame family, and OFX hosts including Blackmagic DaVinci Resolve and Fusion, and Foundry's NUKE. As part of the merger, Boris FX acquired the rights to Particle Illusion. In 2018, Boris FX reintroduced the product to the larger NLE/Compositing market. Sapphire's plug-ins transitioned from C to C++ to improve performance and support higher-resolution visual effects. This update enhanced floating-point calculations, compatibility with film editing APIs, and integration with NVIDIA's CUDA for faster rendering. The plug-ins have been used in various films, including Avatar, the Harry Potter and the Prisoner of Azkaban, Iron Man, The Lord of the Rings, The Matrix trilogy, Titanic, and X-Men. == Particle Illusion == As part of the merger with GenArts in 2016, Boris FX acquired the rights to the Particle Illusion (formerly particleIllusion) product, a storied particle system from the original developer Alan Lorence, the founder of Wondertouch. In 2018, Boris FX released a redesigned version of the product to a larger NLE/compositing market as part of Continuum (2019). The new Particle Illusion plug-in supports Adobe, Avid, and many OFX hosts. == Silhouette == In September 2019, Boris FX merged with SilhouetteFX, Academy Award-winning developer of Silhouette, a high-end digital paint, advanced rotoscoping, motion tracking, and node-based compositing application for visual effects in film post-production. The acquisition integrated Silhouette's advanced rotoscoping and paint technology, recognized by the Academy of Motion Pictures, into Boris FX's suite of products, alongside Sapphire, Continuum, and Mocha Pro. In May 2021, Boris FX released Silhouette 2021, the first version of Silhouette released by Boris FX to function both as a standalone application and as a plug-in for Adobe, Autodesk, Nuke, and other OFX hosts. Silhouette has been used in the visual effects of films such as Avatar, Avengers: Infinity War, Blade Runner 2049, Ex Machina, and Interstellar. == Optics == In June 2020, Boris FX launched Optics, its first plugin deve

  Read more →