In digital signal processing, spatial anti-aliasing is a technique for minimizing the distortion artifacts (aliasing) when representing a high-resolution image at a lower resolution. Anti-aliasing is used in digital photography, computer graphics, digital audio, and many other applications. Anti-aliasing means removing signal components that have a higher frequency than is able to be properly resolved by the recording (or sampling) device. This removal is done before (re)sampling at a lower resolution. When sampling is performed without removing this part of the signal, it causes undesirable artifacts such as black-and-white noise. In signal acquisition and audio, anti-aliasing is often done using an analog anti-aliasing filter to remove the out-of-band component of the input signal prior to sampling with an analog-to-digital converter. In digital photography, optical anti-aliasing filters made of birefringent materials smooth the signal in the spatial optical domain. The anti-aliasing filter essentially blurs the image slightly in order to reduce the resolution to or below that achievable by the digital sensor (the larger the pixel pitch, the lower the achievable resolution at the sensor level). == Examples == In computer graphics, anti-aliasing improves the appearance of "jagged" polygon edges, or "jaggies", so they are smoothed out on the screen. However, it incurs a performance cost for the graphics card and uses more video memory. The level of anti-aliasing determines how smooth polygon edges are (and how much video memory it consumes). Near the top of an image with a receding checker-board pattern, the image is difficult to recognise and often not considered aesthetically pleasing. In contrast, when anti-aliased the checker-board near the top blends into grey, which is usually the desired effect when the resolution is insufficient to show the detail. Even near the bottom of the image, the edges appear much smoother in the anti-aliased image. Multiple methods exist, including the sinc filter, which is considered a better anti-aliasing algorithm. When magnified, it can be seen how anti-aliasing interpolates the brightness of the pixels at the boundaries to produce grey pixels since the space is occupied by both black and white tiles. These help make the sinc filter antialiased image appear much smoother than the original. In a simple diamond image, anti-aliasing blends the boundary pixels; this reduces the aesthetically jarring effect of the sharp, step-like boundaries that appear in the aliased graphic. Anti-aliasing is often applied in rendering text on a computer screen, to suggest smooth contours that better emulate the appearance of text produced by conventional ink-and-paper printing. Particularly with fonts displayed on typical LCD screens, it is common to use subpixel rendering techniques like ClearType. Sub-pixel rendering requires special colour-balanced anti-aliasing filters to turn what would be severe colour distortion into barely-noticeable colour fringes. Equivalent results can be had by making individual sub-pixels addressable as if they were full pixels, and supplying a hardware-based anti-aliasing filter as is done in the OLPC XO-1 laptop's display controller. Pixel geometry affects all of this, whether the anti-aliasing and sub-pixel addressing are done in software or hardware. == Simplest approach to anti-aliasing == The most basic approach to anti-aliasing a pixel is determining what percentage of the pixel is occupied by a given region in the vector graphic - in this case a pixel-sized square, possibly transposed over several pixels - and using that percentage as the colour. A Python program producing a basic plot of a single, white-on-black anti-aliased point using the method is as follows: This method is generally best suited for simple graphics, such as basic lines or curves, and applications that would otherwise have to convert absolute coordinates to pixel-constrained coordinates, such as 3D graphics. It is a fairly fast function, but it is relatively low-quality, and gets slower as the complexity of the shape increases. For purposes requiring very high-quality graphics or very complex vector shapes, this will probably not be the best approach. Note: The plot_antialiased_point routine above cannot blindly set the colour value to the percent calculated. It must add the new value to the existing value at that location up to a maximum of 1. Otherwise, the brightness of each pixel will be equal to the darkest value calculated in time for that location which produces a very bad result. For example, if one point sets a brightness level of 0.90 for a given pixel and another point calculated later barely touches that pixel and has a brightness of 0.05, the final value set for that pixel should be 0.95, not 0.05. For more sophisticated shapes, the algorithm may be generalized as rendering the shape to a pixel grid with higher resolution than the target display surface (usually a multiple that is a power of 2 to reduce distortion), then using bicubic interpolation to determine the average intensity of each real pixel on the display surface. == Signal processing approach to anti-aliasing == In this approach, the ideal image is regarded as a signal. The image displayed on the screen is taken as samples, at each (x,y) pixel position, of a filtered version of the signal. Ideally, one would understand how the human brain would process the original signal, and provide an on-screen image that will yield the most similar response by the brain. The most widely accepted analytic tool for such problems is the Fourier transform; this decomposes a signal into basis functions of different frequencies, known as frequency components, and gives us the amplitude of each frequency component in the signal. The waves are of the form: cos ( 2 j π x ) cos ( 2 k π y ) {\displaystyle \ \cos(2j\pi x)\cos(2k\pi y)} where j and k are arbitrary non-negative integers. There are also frequency components involving the sine functions in one or both dimensions, but for the purpose of this discussion, the cosine will suffice. The numbers j and k together are the frequency of the component: j is the frequency in the x direction, and k is the frequency in the y direction. The goal of an anti-aliasing filter is to greatly reduce frequencies above a certain limit, known as the Nyquist frequency, so that the signal will be accurately represented by its samples, or nearly so, in accordance with the sampling theorem; there are many different choices of detailed algorithm, with different filter transfer functions. Current knowledge of human visual perception is not sufficient, in general, to say what approach will look best. == Two dimensional considerations == The previous discussion assumes that the rectangular mesh sampling is the dominant part of the problem. The filter usually considered optimal is not rotationally symmetrical, as shown in this first figure; this is because the data is sampled on a square lattice, not using a continuous image. This sampling pattern is the justification for doing signal processing along each axis, as it is traditionally done on one dimensional data. Lanczos resampling is based on convolution of the data with a discrete representation of the sinc function. If the resolution is not limited by the rectangular sampling rate of either the source or target image, then one should ideally use rotationally symmetrical filter or interpolation functions, as though the data were a two dimensional function of continuous x and y. The sinc function of the radius has too long a tail to make a good filter (it is not even square-integrable). A more appropriate analog to the one-dimensional sinc is the two-dimensional Airy disc amplitude, the 2D Fourier transform of a circular region in 2D frequency space, as opposed to a square region. One might consider a Gaussian plus enough of its second derivative to flatten the top (in the frequency domain) or sharpen it up (in the spatial domain), as shown. Functions based on the Gaussian function are natural choices, because convolution with a Gaussian gives another Gaussian whether applied to x and y or to the radius. Similarly to wavelets, another of its properties is that it is halfway between being localized in the configuration (x and y) and in the spectral (j and k) representation. As an interpolation function, a Gaussian alone seems too spread out to preserve the maximum possible detail, and thus the second derivative is added. As an example, when printing a photographic negative with plentiful processing capability and on a printer with a hexagonal pattern, there is no reason to use sinc function interpolation. Such interpolation would treat diagonal lines differently from horizontal and vertical lines, which is like a weak form of aliasing. == Practical real-time anti-aliasing approximations == There are only a handful of primitives used at the lowest level in a real-time rend
List of security hacking incidents
This list of security hacking incidents covers important or noteworthy events in the history of security hacking and cracking. == 1900 == === 1903 === Magician and inventor Nevil Maskelyne disrupts John Ambrose Fleming's public demonstration of Guglielmo Marconi's purportedly secure wireless telegraphy technology, sending insulting Morse code messages through the auditorium's projector. == 1930s == === 1932 === Polish cryptologists Marian Rejewski, Henryk Zygalski and Jerzy Różycki broke the Enigma machine code. === 1939 === Alan Turing, Gordon Welchman and Harold Keen worked together to develop the codebreaking device Bombe (based off of Rejewski's work on Bomba). The Enigma machine's use of a reliably small key space makes it vulnerable to brute force attacks. == 1940s == === 1943 === René Carmille, comptroller general of the Vichy French Army, hacked the punch card system used by the Nazis to locate Jews. === 1949 === The theory that underlies computer viruses was first made public in 1949, when computer pioneer John von Neumann presented a paper titled "Theory and Organization of Complicated Automata". In the paper, von Neumann speculated that computer programs could reproduce themselves. == 1950s == === 1955 === At MIT, "hack" first came to mean playing with machines. An April 1955 meeting of the Tech Model Railroad Club has one say that "Mr. Eccles requests that anyone working or hacking on the electrical system turn the power off to avoid fuse blowing." === 1957 === Joe "Joybubbles" Engressia, a blind seven-year-old boy with perfect pitch, discovered that whistling the fourth E above middle C (a frequency of 2600 Hz) would interfere with AT&T's automated telephone systems, thereby inadvertently opening the door for phreaking. == 1960s == Various phreaking boxes are used to interact with automated telephone systems. === 1963 === The first ever reference to malicious hacking is 'phreaking' in MIT's student newspaper, The Tech, containing hackers tying up the lines with Harvard, configuring the PDP-1 to make free calls, war dialing and accumulating large phone bills. === 1965 === William D. Mathews from MIT finds a vulnerability in a CTSS running on an IBM 7094. The standard text editor on the system was designed to be used by one user at a time, working in one directory, and so it created a temporary file with a constant name for all instances of the editor. The flaw was discovered when two system programmers were editing at the same time and the temporary files for the message of the day and the password file became swapped, causing the contents of the system CTSS password file to display to any user logging into the system. === 1967 === The first known incidence of network penetration hacking took place when members of a computer club at a suburban Chicago high school were provided access to IBM's APL network. In the fall of 1967, IBM (through Science Research Associates) approached Evanston Township High School with the offer of four 2741 Selectric teletypewriter-based terminals with dial-up modem connectivity to an experimental computer system which implemented an early version of the APL programming language. The APL network system was structured into workspaces which were assigned to various clients using the system. Working independently, the students quickly learned the language and the system. They were free to explore the system, often using existing code available in public workspaces as models for their own creations. Eventually, curiosity drove the students to explore the system's wider context. This first informal network penetration effort was later acknowledged as helping harden the security of one of the first publicly accessible networks:Science Research Associates undertook to write a full APL system for the IBM 1500. They modeled their system after APL/360, which had by that time been developed and seen substantial use inside of IBM, using code borrowed from MAT/1500 where possible. In their documentation, they acknowledge their gratitude to "a number of high school students for their compulsion to bomb the system". This was an early example of a kind of sportive, but very effective, debugging that was often repeated in the evolution of APL systems. == 1970s == === 1971 === John T. Draper (later nicknamed Captain Crunch), his friend Joe Engressia (also known as Joybubbles), and blue box phone phreaking hit the news with an Esquire magazine feature story. === 1979 === Kevin Mitnick breaks into his first major computer system, the Ark, which was the computer system Digital Equipment Corporation (DEC) used for developing their RSTS/E operating system software. == 1980s == === 1980 === The FBI investigates a breach of security at National CSS (NCSS). The New York Times, reporting on the incident in 1981, describes hackers as: Technical experts, skilled, often young, computer programmers who almost whimsically probe the defenses of a computer system, searching out the limits and the possibilities of the machine. Despite their seemingly subversive role, hackers are a recognized asset in the computer industry, often highly prized. The newspaper describes white hat activities as part of a "mischievous but perversely positive 'hacker' tradition". When a National CSS employee revealed the existence of his password cracker, which he had used on customer accounts, the company chastised him not for writing the software but for not disclosing it sooner. The letter of reprimand stated that "The Company realizes the benefit to NCSS and in fact encourages the efforts of employees to identify security weaknesses to the VP, the directory, and other sensitive software in files". === 1981 === Chaos Computer Club forms in Germany. Ian Murphy, aka Captain Zap, was the first cracker to be tried and convicted as a felon. Murphy broke into AT&T's computers in 1981 and changed the internal clocks that metered billing rates. People were getting late-night discount rates when they called at midday. Of course, the bargain-seekers who waited until midnight to call long distance were hit with high bills. === 1983 === The 414s break into 60 computer systems at institutions ranging from the Los Alamos National Laboratory to Manhattan's Memorial Sloan-Kettering Cancer Center. The incident appeared as the cover story of Newsweek with the title "Beware: Hackers at play". As a result, the U.S. House of Representatives held hearings on computer security and passed several laws. The group KILOBAUD is formed in February, kicking off a series of other hacker groups that formed soon after. The movie WarGames introduces the wider public to the phenomenon of hacking and creates a degree of mass paranoia about hackers and their supposed abilities to bring the world to a screeching halt by launching nuclear ICBMs. The U.S. House of Representatives begins hearings on computer security hacking. In his Turing Award lecture, Ken Thompson mentions "hacking" and describes a security exploit that he calls a "Trojan horse". === 1984 === Someone calling himself Lex Luthor founds the Legion of Doom. Named after a Saturday morning cartoon, the LOD had the reputation of attracting "the best of the best"—until one of the most talented members called Phiber Optik feuded with Legion of Doomer Erik Bloodaxe and got 'tossed out of the clubhouse'. Phiber's friends formed a rival group, the Masters of Deception. The Comprehensive Crime Control Act gives the Secret Service jurisdiction over computer fraud. The Cult of the Dead Cow forms in Lubbock, Texas, and begins publishing its underground ezine. The hacker magazine 2600 begins regular publication, right when TAP was putting out its final issue. The editor of 2600, "Emmanuel Goldstein" (whose real name is Eric Corley), takes his handle from the leader of the resistance in George Orwell's Nineteen Eighty-Four. The publication provides tips for would-be hackers and phone phreaks, as well as commentary on the hacker issues of the day. Today, copies of 2600 are sold at most large retail bookstores. The Chaos Communication Congress, the annual European hacker conference organized by the Chaos Computer Club, is held in Hamburg, Germany. William Gibson's groundbreaking science fiction novel Neuromancer, about "Case", a futuristic computer hacker, is published. Considered the first major cyberpunk novel, it brought into hacker jargon such terms as "cyberspace", "the matrix", "simstim", and "ICE". === 1985 === KILOBAUD is re-organized into P.H.I.R.M. and begins sysopping hundreds of bulletin board systems (BBSs) throughout the United States, Canada, and Europe. The online 'zine Phrack is established. The Hacker's Handbook is published in the UK. The FBI, Secret Service, Middlesex County NJ Prosecutor's Office and various local law enforcement agencies execute seven search warrants concurrently across New Jersey on July 12, 1985, seizing equipment from BBS operators and users alike for "complicity in computer theft", under a n
Polynomial texture mapping
Polynomial texture mapping (PTM), also known as Reflectance Transformation Imaging (RTI), is a technique of imaging and interactively displaying objects under varying lighting conditions to reveal surface phenomena. The data acquisition method is single camera multi light (SCML). == Origins == The method was originally developed by Tom Malzbender of HP Labs in order to generate enhanced 3D computer graphics and it has since been adopted for cultural heritage applications. == Methodology == A series of images is captured in a darkened environment with the camera in a fixed position and the object lit from different angles (Single Camera Multi Light). Interactive software processes and combines the set of images to enable the user inspecting the object to control a virtual light source. The virtual light source may be manipulated to simulate light from different angles and of different intensity or wavelengths to illuminate the surface of artefacts and reveal details. Open-source tools for processing the captured images and publishing the resulting relightable images on the web are freely available. == Applications == Polynomial texture mapping may be used for detailed recording and documentation, 3D modeling, edge detection, and to aid the study of inscriptions, rock art and other artefacts. It has been applied to hundreds of the Vindolanda tablets by the Centre for the Study of Ancient Documents at the University of Oxford in conjunction with the British Museum. It has also been deployed, by Ben Altshuler of the Institute for Digital Archaeology, to scan the Philae obelisk at Kingston Lacy and the Parian Chronicle at the Ashmolean Museum; in both cases scans revealed significant, previously illegible text. Method was also used for identifying microscopic worked antler from Star Carr and recording ancient rock art in Armenia. A 'dome' supporting twenty-four lights has been used to image paintings in the National Gallery and produce polynomial texture maps, providing information on condition phenomena for conservation purposes. Studies of the technique at the National Gallery and Tate concluded that it is an effective tool for documenting changes in the condition of paintings, more easily repeatable than raking light photography, and therefore could be used to assess paintings during structural treatment and before and after loan. Twelve dome-based systems built by the University of Southampton have been used to capture thousands of cuneiform tablets at various museums. The technique is now also finding uses in the field of forensic science, for example in imaging footprints, tyre marks, and indented writing.
Masking (art)
In art, craft, and engineering, masking is the use of materials to protect areas from change, or to focus change on other areas. This can describe either the techniques and materials used to control the development of a work of art by protecting a desired area from change; or a phenomenon that (either intentionally or unintentionally) causes a sensation to be concealed from conscious attention. The term is derived from the word mask, in the sense that it hides the face from view. == In painting == Masking materials supplement a painter's dexterity and choice of applicator to control where paint is laid. Examples include the use of a stencil or masking tape to protect areas which are not to be painted. === Solid masks === Most solid masks require an adhesive to hold the mask in place while work is performed. Some, such as masking tape and frisket, come with adhesive pre-applied. Solid masks are readily available in bulk, and are used in large painting jobs. Paper products Kraft paper Butcher paper Masking tape Plastic film Frisket Polyester tape Stencils Silk screen === Liquid masks === Liquid masks are preferred where precision is needed; they prevent paint from seeping underneath, resulting in clean edges. Care must be taken to remove them without damaging the work underneath. Latex or other polymers Molten wax Gesso, typically a substrate for painting, but can also be applied to achieve masking effects == In photography == Masks used for photography are used to enhance the quality of an image. Representations of a scene—whether film, video display, or printed—do not have the dynamic contrast range available to the human eye looking directly at the same scene. Adjusting the contrast in an image helps restore some of the perceived qualities of the original scene. These adjustments are typically performed on "blown-out" highlights, and "crushed" or "muddy" shadow areas, where clipping has occurred; or on desaturated colors. Photographic masks are peculiar in that they are produced from the image they will alter, an exercise in recursion. Masks used to produce other effects are similar to those used in painting. === Controlling exposure === ==== Film ==== The basic methods of controlling exposure are dodging and burning, which respectively lighten (reduce exposure) and darken (increase exposure) areas of an image. The tools a film photographer uses range from shaped pieces of black material (such as studio foil, foam, and paper) to the photographer's hands. To create a photographic mask, a sheet of negative film is contact-exposed to the original film negative or slide positive in a particular way. Both films are then combined to produce a processed positive. The process is similar when applied using digital techniques: the inverse of the working image is reduced to an image mask; filters or other adjustments are then applied, using the mask to selectively block portions of the image. ==== Digital ==== Image editors offer at the very least a "Select All" command and a rectangular "marquee" selection tool. (The word "marquee" describes the "crawling ants" border used to highlight the active region.) Once a selection is created, further changes to the image will be confined to that area. To continue editing the rest of the image, the selection is either "deselected" or the entire image is selected. Advanced suites offer more ways to select portions of an image, as well as ways to combine these selections through. Selection masks can be switched between an editable greyscale image and a mask. They allow the user to create a mask using the suite's painting tools. === Contrast masking === When the contrast range of an image needs to be adjusted, a contrast mask is a simple solution. The processed image resembles what would be achieved when exposing through a neutral density filter, but the effects are focused highly upon the extreme regions of the image. The blocking areas of the mask coincide with the highlights of the image, and the permissive areas with the shadows, resulting in more detail appearing in each. ==== Film ==== The mask is often made from high-quality black-and-white film, such as Kodak Technical Pan, which allows for a degree of softening on the mask. Its processing time is reduced so as to not completely oppose the original negative. Both negatives are combined and registered, and collectively exposed with additional time to compensate for the presence of the mask. ==== Digital ==== Contrast masking is made simpler with digital editing. A grayscale version of the image is produced, either by desaturation or by calculating selected ratios of the image's color channels, inverted, and blurred. The mask and original image are blended together to produce the final processed image. Some image editors allow for refinement of the effect by changing the strength of the blend. Contrast masking can be considered to be the opposite of gamma correction, which adjusts the midtones of an image. Effects similar to contrast masking can be achieved by adjusting the response curves of an image. === Unsharp masking === A derivative of contrast masking is unsharp masking, an unusual term for a process intended to increase the apparent sharpness (acutance) of an image. Unsharp masking uses a blurred form of the image to increase contrast along regions of moderate contrast difference. Around edges, the blur region causes highlights to overexpose and shadows to underexpose. Taken to an extreme, the edges become overly visible and detract from the quality of the image—this is referred to as halation. Unsharp masking does not increase the actual sharpness, as it cannot recover details lost to blurring. ==== Film ==== Unsharp masking allows the photographer to sharpen areas that have become blurred in the original negative, due to long shutter speed/exposure time, or from using a wide aperture/"fast" lens. When creating the unsharp mask, extra space or diffusing material is added between the image and the mask to produce the necessary blur. ==== Digital ==== Unsharp masking has become automated in digital editing, with higher-end suites offering the process as a "tool" or "filter" in their standard sharpening kits—the actual creation of a mask is bypassed in favor of calculations that represent the mask's effect. The process depends on three factors: the radius of the blur, the strength of the effect, and the threshold degree of contrast above which the effect will be applied. (Adjusting the threshold allows the editor to apply the effect selectively upon moderately defined edges and ignore image noise.) Unsharp masking is computationally more complex than other sharpening algorithms, but results in a higher-quality remedy. Deconvolution allows for truer sharpening, but is much more complex than unsharp masking.
Edits (app)
Edits is an American photo and short form video editing software service owned by Meta Platforms. It allows users to create videos and edit them by using features like green screens, and AI animation, and also provides real-time statistics to Instagram creators to track their accounts. Accounts directly from Instagram can be imported, and videos can be exported vice-versa. It is available solely on iOS and Android. On Apple, it supports over 32 different languages, including French, Spanish, and Chinese. It has been noted by critics as a direct competitor for apps like CapCut, owned by Chinese brand ByteDance. The Instagram head, Adam Mosseri, also acknowledged these similarities. Launched on April 22 for both iOS and Android. It received over 5M+ users on Apple and Android combined in its first 4 days since its launch. == History == On January 19, 2025, following the ban of all ByteDance Apps from the Google Play Store, and App Store, Instagram head Adam Mosseri announced on Threads that they would be launching the app in February for iOS, followed by an Android counterpart. He said the app is working with select people to test its features. In a separate post, he emphasized that the app is "more for creators than casual video makers". == Features == Edits contains many similar features to other competition of video editors like KineMaster, Inshot, and CapCut. When creating a video, users have the option to export in resolution of HD, 4K, and 2K, along with having HDR and SDR support. Like many traditional video editing software, it includes a timeline, and basic undo-redo buttons. On the bottom bar, 7 tabs for editing exist, namely the Split, Volume, Adjust, Speed, Delete, Filters, Green Screen, Voice FX, Extract Audio, Mirror, Slip, Replace and Duplicate bars. Basic features, like splitting, and adjusting speed and volume of clips are present, along with more advanced Green Screens, and AI features. Being a mobile video editor app, Edits also has drag-and-drop features to ease customer usage. Users have the ability to record videos directly within the app. This feature allows users to create content without needing extra software or devices. They can choose from several focal lengths, which affect how close or wide the shot appears. The app also supports different frame rates. Users have the ability to record videos directly within the app. This feature allows users to create content without needing extra software or devices. Once users are done filming your clips, they can simply transfer them into a project to start editing immediately. Upcoming features for the app include Keyframes, AI-powered modification, Collaboration, and Enhanced creativity. == Reception == Since its release, it received over 5 million downloads in 4 days. Critically, the app received great rankings from many. From users, the app received an average of 4.45 stars over Google Play Store and App Store in the first few days, with Google Play Store receiving the least stars. As in reviews, it was received mixed by the public. Many people praised the smoothness and intuivity of the app. "The app is more than just a basic editor, offering a full suite of creative tools, including a dedicated tab for inspiration and trending audio, as well as a tab for managing drafts," said a blogger. Some users were disappointed with the range of editing tools, some users have noted that it could benefit from more transition options between clips. Some even reported crashing between clips.
Pattern playback
The pattern playback is an early talking device that was built by Dr. Franklin S. Cooper and his colleagues, including John M. Borst and Caryl Haskins, at Haskins Laboratories in the late 1940s and completed in 1950. There were several different versions of this hardware device. Only one currently survives. The machine converts pictures of the acoustic patterns of speech in the form of a spectrogram back into sound. Using this device, Alvin Liberman, Frank Cooper, and Pierre Delattre (later joined by Katherine Safford Harris, Leigh Lisker, and others) were able to discover acoustic cues for the perception of phonetic segments (consonants and vowels). This research was fundamental to the development of modern techniques of speech synthesis, reading machines for the blind, the study of speech perception and speech recognition, and the development of the motor theory of speech perception. To create sound, the pattern playback machine uses an arc light source which is directed against a rotating disk with 50 concentric tracks whose transparencies vary systematically in order to produce 50 harmonics of a fundamental frequency. The light is further projected against a spectrogram, whose reflectance corresponds to the sound pressure level of the partial of the signal, and is then directed towards a photovoltaic cell by which the light variation is converted into sound pressure variations. The pattern playback was last used in an experimental study by Robert Remez in 1976. The pattern playback now resides in the Museum at Haskins Laboratories in New Haven, Connecticut. The technique of pattern playback also now refers, more generally, to algorithms or techniques for converting spectrograms, cochleagrams, and correlograms from pictures back into sounds. A demonstration is in the TV show Adventure. Pioneering technology in psycholinguistics (CBS Television. 1953). == Digital pattern playback == In the 1970s, digital pattern playbacks began to supplant the earlier version. An early prototype was developed by Patrick Nye, Philip Rubin, and colleagues at Haskins Laboratories. It combined a "Ubiquitous Spectrum Analyzer"[1] for automatic spectral analysis, along with a VAX GT-40 display processor for graphic manipulation of the displayed spectrogram, a form of "synthesis by art", and subsequent re-synthesis using a 40 channel filter bank. This hybrid hardware/software digital pattern playback was eventually replaced at Haskins Laboratories by the HADES analysis and display system, designed by Philip Rubin, and implemented in Fortran on the VAX family of computers. A more modern version has been described by Arai and colleagues [2]. An on-line demonstration is available [3].
Odor source localization
Odor source localization (OSL) is the problem of locating the origin of an airborne or waterborne chemical plume using one or more mobile sensors, typically robots equipped with chemical sensors. The task sits at the intersection of robotics, fluid dynamics and machine olfaction. Chemical plumes in turbulent flows are intermittent and patchy, and most chemical sensors respond slowly and have limited selectivity, so the instantaneous reading available to a moving sensor is a poor proxy for the underlying time-averaged concentration field. Robotic OSL has been studied since the late 1980s and has applications including the detection of gas leaks, search and rescue after industrial accidents, and environmental monitoring of industrial emissions. == History == Robotic odor search emerged in the late 1980s and 1990s, drawing on earlier work in chemical ecology that had described how moths and other insects locate distant pheromone sources. R. A. Russell at Monash University was among the first to build mobile robots that followed chemical trails on the floor and tracked airborne odor plumes. Distributed and multi-robot odor search were investigated by Hayes, Martinoli and Goodman at the California Institute of Technology and EPFL, who studied cooperative plume-tracing on simulated and physical robot swarms. In 2007 Vergassola, Villermaux and Shraiman introduced infotaxis, an information-theoretic search strategy in which a sensor moves so as to maximize the expected information gain about source location, rather than following a chemical concentration gradient; the paper appeared in Nature and prompted substantial follow-up work in the robotics community. From the mid-2010s, multi-rotor unmanned aerial vehicles carrying lightweight chemical sensors became a common experimental platform for OSL research. == Problem formulation == OSL is generally decomposed into three sub-problems: plume detection (deciding whether a chemical signal is present), plume traversal (moving so as to remain in contact with the plume), and source declaration (deciding when the source has been reached). The mathematical difficulty depends strongly on the assumed dispersion model. In laminar or low-Reynolds number flows a Gaussian advection–diffusion model gives a smooth concentration field with a well-defined gradient. In turbulent flows, which dominate most realistic environments, the plume is filamentary: the sensor receives short, randomly spaced bursts of chemical separated by periods of zero signal, and the time-averaged field is not a useful guide on the time scales at which a robot must act. Source-term estimation, surveyed by Hutchinson and colleagues, additionally aims to recover both the position and the release rate of the source from the observed concentrations, often using probabilistic filters. == Biological inspiration == Many OSL strategies are explicitly modeled on the behavior of male moths flying upwind toward a pheromone source. As reviewed by Cardé and Willis, moths combine an upwind surge whenever they detect a filament of pheromone with a wider crosswind cast when contact is lost, producing a characteristic zig-zag trajectory that has been transposed onto mobile robots by several groups. Other biological models draw on the search behavior of dogs and of marine animals such as blue crabs and lobsters, which integrate chemical and bilateral hydrodynamic cues over much shorter ranges. == Algorithms and strategies == === Reactive strategies === Reactive strategies select the next motion as a direct function of the current sensor reading. Chemotaxis steers along the locally estimated concentration gradient, which is effective in laminar plumes but degrades severely in turbulence. Anemotaxis exploits a measured wind direction by surging upwind when chemical contact is made. The bio-inspired cast-and-surge family combines anemotaxis with a deterministic crosswind cast on contact loss, and is the dominant reactive approach for turbulent environments. === Probabilistic and information-theoretic strategies === Probabilistic methods maintain a posterior distribution over possible source locations and choose actions that improve that distribution. The infotaxis strategy of Vergassola, Villermaux and Shraiman selects the move that maximizes the expected reduction in entropy of the source-location posterior, and is effective in regimes where the spatial gradient is unusable. Bayesian source-term estimation extends this idea by inferring both source position and release rate, typically using particle filters or sequential Monte Carlo. === Map-based strategies === Map-based methods build a spatial model of the time-averaged gas distribution from sensor readings collected along the robot's trajectory and search for local maxima in that model. Lilienthal and colleagues describe a family of kernel-based gas distribution mapping techniques in which point measurements are convolved with a Gaussian kernel to produce a spatially extrapolated estimate. Such methods are most useful when the source can be assumed quasi-stationary and the robot is able to revisit locations. === Multi-robot and swarm strategies === Multiple robots searching cooperatively can shorten search times. Cooperative formations spread the sensors across the crosswind axis, making detection of an intermittent plume more likely. Swarm-based approaches, reviewed by Wang and colleagues, deploy larger numbers of simpler agents and rely on collective behavior rather than centralized planning; reported advantages include improved coverage of the search area and the possibility of locating multiple sources in parallel. == Sensors and platforms == Most OSL systems use metal-oxide semiconductor (MOX) sensors, photoionization detectors or electrochemical cells, which trade off sensitivity, selectivity, response time and power consumption. Ishida and colleagues describe how these sensors interact with airflow around the robot body, an effect that motivates careful aerodynamic design and active sampling. Mobile platforms include wheeled ground robots for indoor and structured outdoor environments, multi-rotor unmanned aerial vehicles for open spaces and elevated sources, and autonomous underwater vehicles for chemical plumes in the marine environment. == Notable systems == Among the early demonstrations, R. A. Russell's series of differential-drive robots at Monash University localized volatile sources in still and ventilated rooms during the 1990s. The Smelling Nano Aerial Vehicle reported by Burgués and colleagues used a Crazyflie nano-quadcopter (approximately 27 grams in mass and 10 cm across) carrying a custom MOX gas sensing board, and built three-dimensional gas distribution maps of indoor releases from sweeping flights of less than three minutes. The GADEN simulator, released by Monroy and colleagues, couples three-dimensional dispersion computed from an OpenFOAM CFD solver with models of MOX and photo-ionization gas sensors, and is widely used to test mobile-robot olfaction algorithms in simulation. == Applications == Reported applications include the localization of natural-gas and methane leaks in urban infrastructure, search for chemical contamination after industrial accidents, search and rescue, and environmental monitoring of industrial emissions. Drug- and explosives-detection robots are an adjacent application area, although these typically rely on close-range sniffing rather than long-range plume tracking. == Open challenges == Open challenges identified in recent reviews include the limited speed, selectivity and stability of available chemical sensors; the scarcity of standardized, large-scale benchmarks comparable to those available in computer vision; reliable handling of multi-source environments, where standard single-source assumptions fail; and the integration of OSL with other autonomous-vehicle subsystems such as obstacle avoidance and navigation in three-dimensional turbulent flow.