Hall circles (also known as M-circles and N-circles) are a graphical tool in control theory used to obtain values of a closed-loop transfer function from the Nyquist plot (or the Nichols plot) of the associated open-loop transfer function. Hall circles have been introduced in control theory by Albert C. Hall in his thesis. == Construction == Consider a closed-loop linear control system with open-loop transfer function given by transfer function G ( s ) {\displaystyle G(s)} and with a unit gain in the feedback loop. The closed-loop transfer function is given by T ( s ) = G ( s ) 1 + G ( s ) {\textstyle T(s)={\frac {G(s)}{1+G(s)}}} . To check the stability of T(s), it is possible to use the Nyquist stability criterion with the Nyquist plot of the open-loop transfer function G(s). Note, however, that the Nyquist plot of G(s) does not give the actual values of T(s). To get this information from the G(s)-plane, Hall proposed to construct the locus of points in the G(s)-plane such that T(s) has constant magnitude and also the locus of points in the G(s)-plane such that T(s) has constant phase angle. Given a positive real value M representing a fixed magnitude, and denoting G(s) by z, the points satisfying M = | T ( s ) | = | G ( s ) | | 1 + G ( s ) | = | z | | 1 + z | {\displaystyle M=|T(s)|={\frac {|G(s)|}{|1+G(s)|}}={\frac {|z|}{|1+z|}}} are given by the points z in the G(s)-plane such that the ratio of the distance between z and 0 and the distance between z and -1 is equal to M. The points z satisfying this locus condition are circles of Apollonius, and this locus is known in the context of control systems as M-circles. Given a positive real value N representing a phase angle, the points satisfying N = arg [ G ( s ) 1 + G ( s ) ] = arg [ G ( s ) ] − arg [ 1 + G ( s ) ] = arg [ z ] − arg [ 1 + z ] {\displaystyle N=\arg \left[{\frac {G(s)}{1+G(s)}}\right]=\arg[G(s)]-\arg[1+G(s)]=\arg[z]-\arg[1+z]} are given by the points z in the G(s)-plane such that the angle between -1 and z and the angle between 0 and z is constant. In other words, the angle opposed to the line segment between -1 and 0 must be constant. This implies that the points z satisfying this locus condition are arcs of circles, and this locus is known in the context of control systems as N-circles. == Usage == To use the Hall circles, a plot of M and N circles is done over the Nyquist plot of the open-loop transfer function. The points of the intersection between these graphics give the corresponding value of the closed-loop transfer function. Hall circles are also used with the Nichols plot and in this setting, are also known as Nichols chart. Rather than overlaying directly the Hall circles over the Nichols plot, the points of the circles are transferred to a new coordinate system where the ordinate is given by 20 log 10 ( | G ( s ) | ) {\displaystyle 20\log _{10}(|G(s)|)} and the abscissa is given by arg ( G ( s ) ) {\displaystyle \arg(G(s))} . The advantage of using Nichols chart is that adjusting the gain of the open loop transfer function directly reflects in up and down translation of the Nichols plot in the chart.
Digital transaction management
Digital transaction management (DTM) is a category of cloud services designed to digitally manage document-based transactions. DTM removes the friction inherent in transactions that involve people, documents, and data to create faster, easier, more convenient, and secure processes. DTM goes beyond content and document management to include e-signatures, authentication and non-repudiation; enabling co-browsing between the customer and the business; document transfer and certification; secure archiving that goes beyond records management; and a variety of meta-processes around managing electronic transactions and the documents associated with them. DTM standards are proposed and managed by the xDTM Standard Association Aragon Research has estimated that "by YE 2016, 70% of large enterprises will have a DTM initiative underway or fully implemented."
Hybrid machine translation
Hybrid machine translation is a method of machine translation that is characterized by the use of multiple machine translation approaches within a single machine translation system. The motivation for developing hybrid machine translation systems stems from the failure of any single technique to achieve a satisfactory level of accuracy. Many hybrid machine translation systems have been successful in improving the accuracy of the translations, and there are several popular machine translation systems which employ hybrid methods. == Approaches == === Multi-engine === This approach to hybrid machine translation involves running multiple machine translation systems in parallel. The final output is generated by combining the output of all the sub-systems. Most commonly, these systems use statistical and rule-based translation subsystems, but other combinations have been explored. For example, researchers at Carnegie Mellon University have had some success combining example-based, transfer-based, knowledge-based and statistical translation sub-systems into one machine translation system. === Statistical rule generation === This approach involves using statistical data to generate lexical and syntactic rules. The input is then processed with these rules as if it were a rule-based translator. This approach attempts to avoid the difficult and time-consuming task of creating a set of comprehensive, fine-grained linguistic rules by extracting those rules from the training corpus. This approach still suffers from many problems of normal statistical machine translation, namely that the accuracy of the translation will depend heavily on the similarity of the input text to the text of the training corpus. As a result, this technique has had the most success in domain-specific applications, and has the same difficulties with domain adaptation as many statistical machine translation systems. === Multi-Pass === This approach involves serially processing the input multiple times. The most common technique used in multi-pass machine translation systems is to pre-process the input with a rule-based machine translation system. The output of the rule-based pre-processor is passed to a statistical machine translation system, which produces the final output. This technique is used to limit the amount of information a statistical system need consider, significantly reducing the processing power required. It also removes the need for the rule-based system to be a complete translation system for the language, significantly reducing the amount of human effort and labor necessary to build the system. === Confidence-Based === This approach differs from the other hybrid approaches in that in most cases only one translation technology is used. A confidence metric is produced for each translated sentence from which a decision can be made whether to try a secondary translation technology or to proceed with the initial translation output. SMT is also used when common error patterns such as multiple repeat words appear in sequence, as is common with NMT when the attention mechanism is confused.
Underwater computer vision
Underwater computer vision is a subfield of computer vision. In recent years, with the development of underwater vehicles ( ROV, AUV, gliders), the need to be able to record and process huge amounts of information has become increasingly important. Applications range from inspection of underwater structures for the offshore industry to the identification and counting of fishes for biological research. However, no matter how big the impact of this technology can be to industry and research, it still is in a very early stage of development compared to traditional computer vision. One reason for this is that, the moment the camera goes into the water, a whole new set of challenges appear. On one hand, cameras have to be made waterproof, marine corrosion deteriorates materials quickly and access and modifications to experimental setups are costly, both in time and resources. On the other hand, the physical properties of the water make light behave differently, changing the appearance of a same object with variations of depth, organic material, currents, temperature etc. == Applications == Seafloor survey Vehicle navigation and positioning Biological monitoring {possibly aquatic biomonitoring) Video mosaics as visual navigation maps Submarine pipeline inspection Wreckage visualization Maintenance of underwater structures Drowning detection systems == Medium differences == === Illumination === In air, light comes from the whole hemisphere on cloudy days, and is dominated by the sun. In water direct lighting comes from a cone about 96° wide above the scene. This phenomenon is called Snell's window. Artificial lighting can be used where natural light levels are insufficient and where the light path is too long to produce acceptable colour, as the loss of colour is a function of the total distance through water from the source to the camera lens port. === Light attenuation === Unlike air, water attenuates light exponentially. This results in hazy images with very low contrast. The main reasons for light attenuation are light absorption (where energy is removed from the light) and light scattering, by which the direction of light is changed. Light scattering can further be divided into forward scattering, which results in an increased blurriness and backward scattering that limits the contrast and is responsible for the characteristic veil of underwater images. Both scattering and attenuation are heavily influenced by the amount of organic matter dissolved or suspended in the water. Light attenuation in water is also a function of the wavelength. This means that different colours are attenuated at different rates, leading to colour degradation.with depth and distance. Red and orange light are attenuated faster, followed by yellows and greens. Blue is the least attenuated visible wavelength. === Artificial lighting === == Challenges == In high level computer vision, human structures are frequently used as image features for image matching in different applications. However, the sea bottom lacks such features, making it hard to find correspondences in two images. In order to be able to use a camera in the water, a watertight housing is required. However, refraction will happen at the water-glass and glass-air interface due to differences in density of the materials. This has the effect of introducing a non-linear image deformation. The motion of the vehicle presents another special challenge. Underwater vehicles are constantly moving due to currents and other phenomena. This introduces another uncertainty to algorithms, where small motions may appear in all directions. This can be specially important for video tracking. In order to reduce this problem image stabilization algorithms may be applied. == Relevant technology == === Image restoration === Image restoration< techniques are intended to model the degradation process and then invert it, obtaining the new image after solving. It is generally a complex approach that requires plenty of parameters that vary a lot between different water conditions. === Image enhancement === Image enhancement only tries to provide a visually more appealing image without taking the physical image formation process into account. These methods are usually simpler and less computational intensive. === Color correction === Various algorithms exist that perform automatic color correction. The UCM (Unsupervised Color Correction Method), for example, does this in the following steps: It firstly reduces the color cast by equalizing the color values. Then it enhances contrast by stretching the red histogram towards the maximum and finally saturation and intensity components are optimized. == Underwater stereo vision == It is usually assumed that stereo cameras have been calibrated previously, geometrically and radiometrically. This leads to the assumption that corresponding pixels should have the same color. However this can not be guaranteed in an underwater scene, because of dispersion and backscatter. However, it is possible to digitally model this phenomenon and create a virtual image with those effects removed == Other application fields == Imaging sonars have become more and more accessible and gained resolution, delivering better images. Sidescan sonars are used to produce complete maps of regions of the sea floor stitching together sequences of sonar images. However, sonar images often lack proper contrast and are degraded by artefacts and distortions due to noise, attitude changes of the AUV/ROV carrying the sonar or non uniform beam patterns. Another common problem with sonar computer vision is the comparatively low frame rate of sonar images.
1.58-bit large language model
A 1.58-bit large language model (also known as a ternary LLM) is a type of large language model (LLM) designed to be computationally efficient. It achieves this by using weights that are restricted to only three values: -1, 0, and +1. This restriction significantly reduces the model's memory footprint and allows for faster processing, as computationally expensive multiplication operations can be replaced with lower-cost additions. This contrasts with traditional models that use 16-bit floating-point numbers (FP16 or BF16) for their weights. Studies have shown that for models up to several billion parameters, the performance of 1.58-bit LLMs on various tasks is comparable to their full-precision counterparts. This approach could enable powerful AI to run on less specialized and lower-power hardware. The name "1.58-bit" comes from the fact that a system with three states contains log 2 3 ≈ 1.58 {\displaystyle \log _{2}3\approx 1.58} bits of information. These models are sometimes also referred to as 1-bit LLMs in research papers, although this term can also refer to true binary models (with weights of -1 and +1). == BitNet == In 2024, Ma et al., researchers at Microsoft, declared that their 1.58-bit model, BitNet b1.58 is comparable in performance to the 16-bit Llama 2 and opens the era of 1-bit LLM. BitNet creators did not use the post-training quantization of weights but instead relied on the new BitLinear transform that replaced the nn.Linear layer of the traditional transformer design. In 2025, Microsoft researchers had released an open-weights and open inference code model BitNet b1.58 2B4T demonstrating performance competitive with the full precision models at 2B parameters and 4T training tokens. == Post-training quantization == BitNet derives its performance from being trained natively in 1.58 bit instead of being quantized from a full-precision model after training. Still, training is an expensive process and it would be desirable to be able to somehow convert an existing model to 1.58 bits. In 2024, HuggingFace reported a way to gradually ramp up the 1.58-bit quantization in fine-tuning an existing model down to 1.58 bits. == Critique == Some researchers point out that the scaling laws of large language models favor the low-bit weights only in case of undertrained models. As the number of training tokens increases, the deficiencies of low-bit quantization surface.
Histogram of oriented displacements
Histogram of oriented displacements (HOD) is a 2D trajectory descriptor. The trajectory is described using a histogram of the directions between each two consecutive points. Given a trajectory T = {P1, P2, P3, ..., Pn}, where Pt is the 2D position at time t. For each pair of positions Pt and Pt+1, calculate the direction angle θ(t, t+1). Value of θ is between 0 and 360. A histogram of the quantized values of θ is created. If the histogram is of 8 bins, the first bin represents all θs between 0 and 45. The histogram accumulates the lengths of the consecutive moves. For each θ, a specific histogram bin is determined. The length of the line between Pt and Pt+1 is then added to the specific histogram bin. To show the intuition behind the descriptor, consider the action of waving hands. At the end of the action, the hand falls down. When describing this down movement, the descriptor does not care about the position from which the hand started to fall. This fall will affect the histogram with the appropriate angles and lengths, regardless of the position where the hand started to fall. HOD records for each moving point: how much it moves in each range of directions. HOD has a clear physical interpretation. It proposes that, a simple way to describe the motion of an object, is to indicate how much distance it moves in each direction. If the movement in all directions are saved accurately, the movement can be repeated from the initial position to the final destination regardless of the displacements order. However, the temporal information will be lost, as the order of movements is not stored-this is what we solve by applying the temporal pyramid, as shown in section \ref{sec:temp-pyramid}. If the angles quantization range is small, classifiers that use the descriptor will overfit. Generalization needs some slack in directions-which can be done by increasing the quantization range.
Textual entailment
In natural language processing, textual entailment (TE), also known as natural language inference (NLI), is a directional relation between text fragments. The relation holds whenever the truth of one text fragment follows from another text. == Definition == In the TE framework, the entailing and entailed texts are termed text (t) and hypothesis (h), respectively. Textual entailment is not the same as pure logical entailment – it has a more relaxed definition: "t entails h" (t ⇒ h) if, typically, a human reading t would infer that h is most likely true. (Alternatively: t ⇒ h if and only if, typically, a human reading t would be justified in inferring the proposition expressed by h from the proposition expressed by t.) The relation is directional because even if "t entails h", the reverse "h entails t" is much less certain. Determining whether this relationship holds is an informal task, one which sometimes overlaps with the formal tasks of formal semantics (satisfying a strict condition will usually imply satisfaction of a less strict conditioned); additionally, textual entailment partially subsumes word entailment. == Examples == Textual entailment can be illustrated with examples of three different relations: An example of a positive TE (text entails hypothesis) is: text: If you help the needy, God will reward you. hypothesis: Giving money to a poor man has good consequences. An example of a negative TE (text contradicts hypothesis) is: text: If you help the needy, God will reward you. hypothesis: Giving money to a poor man has no consequences. An example of a non-TE (text does not entail nor contradict) is: text: If you help the needy, God will reward you. hypothesis: Giving money to a poor man will make you a better person. == Ambiguity of natural language == A characteristic of natural language is that there are many different ways to state what one wants to say: several meanings can be contained in a single text and the same meaning can be expressed by different texts. This variability of semantic expression can be seen as the dual problem of language ambiguity. Together, they result in a many-to-many mapping between language expressions and meanings. The task of paraphrasing involves recognizing when two texts have the same meaning and creating a similar or shorter text that conveys almost the same information. Textual entailment is similar but weakens the relationship to be unidirectional. Mathematical solutions to establish textual entailment can be based on the directional property of this relation, by making a comparison between some directional similarities of the texts involved. == Approaches == Textual entailment measures natural language understanding as it asks for a semantic interpretation of the text, and due to its generality remains an active area of research. Many approaches and refinements of approaches have been considered, such as word embedding, logical models, graphical models, rule systems, contextual focusing, and machine learning. Practical or large-scale solutions avoid these complex methods and instead use only surface syntax or lexical relationships, but are correspondingly less accurate. As of 2005, state-of-the-art systems are far from human performance; a study found humans to agree on the dataset 95.25% of the time. Algorithms from 2016 had not yet achieved 90%. == Applications == Many natural language processing applications, like question answering, information extraction, summarization, multi-document summarization, and evaluation of machine translation systems, need to recognize that a particular target meaning can be inferred from different text variants. Typically entailment is used as part of a larger system, for example in a prediction system to filter out trivial or obvious predictions. Textual entailment also has applications in adversarial stylometry, which has the objective of removing textual style without changing the overall meaning of communication. == Datasets == Some of available English NLI datasets include: SNLI MultiNLI SciTail SICK MedNLI QA-NLI In addition, there are several non-English NLI datasets, as follows: XNLI DACCORD, RTE3-FR, SICK-FR for French FarsTail for Farsi OCNLI for Chinese SICK-NL for Dutch IndoNLI for Indonesian