In electrical engineering and telecommunications, a line splice is a joint directly connecting lengths of electrical cables (electrical splice) or optical fibers (optical splice). The splices are often protected by sleeves. == Splicing of copper wires == The splicing of copper wires happens in the following steps: The cores are laid one above the other at the junction. The core insulation is removed. The wires are wrapped two to three times around each other (twisting). The bare veins on a length of about 3 cm "strangle" or "twist". In some cases, the strangulation is soldered. To isolate the splice, an insulating sleeve made of paper or plastic is pushed over it. The splicing of copper wires is mainly used on paper insulated wires. LSA techniques (LSA: soldering, screwing and stripping free) are used to connect copper wires, making the copper wires faster and easier to connect. LSA techniques include: Wire connection sleeves (AVH = Adernverbindungshülsen) and other crimp connectors. The two wires to be connected are inserted into the AVH without being stripped, which is then compressed with special pliers. The about 2 cm long AVH consist of contact, pressure and insulation. For wire connection strips (AVL = Adernverbindungsleisten) several pairs of wires (10 = AVL10 or 20 = AVL20) are inserted, the strip is then closed with a lid and pressed together with a hydraulic press, which ensures the connection. == Splicing of glass fibers == Fiber-optic cables are spliced using a special arc-splicer, with installation cables connected at their ends to respective "pigtails" - short individual fibers with fiber-optic connectors at one end. The splicer precisely adjusts the light-guiding cores of the two ends of the glass fibers to be spliced. The adjustment is done fully automatically in modern devices, whereas in older models this is carried out manually by means of micrometer screws and microscope. An experienced splicer can precisely position the fiber ends within a few seconds. Subsequently, the fibers are fused together (welded) with an electric arc. Since no additional material is added, such as gas welding or soldering, this is called a "fusion splice". Depending on the quality of the splicing process, attenuation values at the splice points are achieved by 0.3 dB, with good splices also below 0.02 dB. For newer generation devices, alignment is done automatically by motors. Here one differentiates core and jacket centering. At core centering (usually single-mode fibers), the fiber cores are aligned. A possible core offset with respect to the jacket is corrected. In the jacket centering (usually in multimode fibers), the fibers are adjusted to each other by means of electronic image processing in front of the splice. When working with good equipment, the damping value is according to experience at max. 0.1 dB. Measurements are made by means of special measuring devices including optical time-domain reflectometry (OTDR). A good splice should have an attenuation of less than 0.3 dB over the entire distance. Finished fiber optic splices are housed in splice boxes. One differentiates: Fusion splice Adhesive splicing Crimp splice or NENP (no-epoxy no-polish), mechanical splice
Tensor (machine learning)
In machine learning, the term tensor informally refers to two different concepts: (i) a way of organizing data and (ii) a multilinear (tensor) transformation. Data may be organized in a multidimensional array (M-way array), informally referred to as a "data tensor"; however, in the strict mathematical sense, a tensor is a multilinear mapping over a set of domain vector spaces to a range vector space. Observations, such as images, movies, volumes, sounds, and relationships among words and concepts, stored in an M-way array ("data tensor"), may be analyzed either by artificial neural networks or tensor methods. Tensor decomposition factors data tensors into smaller tensors. Operations on data tensors can be expressed in terms of matrix multiplication and the Kronecker product. The computation of gradients, a crucial aspect of backpropagation, can be performed using software libraries such as PyTorch and TensorFlow. Computations are often performed on graphics processing units (GPUs) using CUDA, and on dedicated hardware such as Google's Tensor Processing Unit or Nvidia's Tensor core. These developments have greatly accelerated neural network architectures, and increased the size and complexity of models that can be trained. == History == A tensor is by definition a multilinear map. In mathematics, this may express a multilinear relationship between sets of algebraic objects. In physics, tensor fields, considered as tensors at each point in space, are useful in expressing mechanics such as stress or elasticity. In machine learning, the exact use of tensors depends on the statistical approach being used. In 2001, the field of signal processing and statistics were making use of tensor methods. Pierre Comon surveys the early adoption of tensor methods in the fields of telecommunications, radio surveillance, chemometrics and sensor processing. Linear tensor rank methods (such as, Parafac/CANDECOMP) analyzed M-way arrays ("data tensors") composed of higher order statistics that were employed in blind source separation problems to compute a linear model of the data. He noted several early limitations in determining the tensor rank and efficient tensor rank decomposition. In the early 2000s, multilinear tensor methods crossed over into computer vision, computer graphics and machine learning with papers by Vasilescu or in collaboration with Terzopoulos, such as Human Motion Signatures, TensorFaces TensorTextures and Multilinear Projection. Multilinear algebra, the algebra of higher-order tensors, is a suitable and transparent framework for analyzing the multifactor structure of an ensemble of observations and for addressing the difficult problem of disentangling the causal factors based on second order or higher order statistics associated with each causal factor. Tensor (multilinear) factor analysis disentangles and reduces the influence of different causal factors with multilinear subspace learning. When treating an image or a video as a 2- or 3-way array, i.e., "data matrix/tensor", tensor methods reduce spatial or time redundancies as demonstrated by Wang and Ahuja. Yoshua Bengio, Geoff Hinton and their collaborators briefly discuss the relationship between deep neural networks and tensor factor analysis beyond the use of M-way arrays ("data tensors") as inputs. One of the early uses of tensors for neural networks appeared in natural language processing. A single word can be expressed as a vector via Word2vec. Thus a relationship between two words can be encoded in a matrix. However, for more complex relationships such as subject-object-verb, it is necessary to build higher-dimensional networks. In 2009, the work of Sutskever introduced Bayesian Clustered Tensor Factorization to model relational concepts while reducing the parameter space. From 2014 to 2015, tensor methods become more common in convolutional neural networks (CNNs). Tensor methods organize neural network weights in a "data tensor", analyze and reduce the number of neural network weights. Lebedev et al. accelerated CNN networks for character classification (the recognition of letters and digits in images) by using 4D kernel tensors. == Definition == Let F {\displaystyle \mathbb {F} } be a field (such as the real numbers R {\displaystyle \mathbb {R} } or the complex numbers C {\displaystyle \mathbb {C} } ). A tensor T ∈ F I 1 × I 2 × … × I C {\displaystyle {\mathcal {T}}\in {\mathbb {F} }^{I_{1}\times I_{2}\times \ldots \times I_{C}}} is a multilinear transformation from a set of domain vector spaces to a range vector space: T : { F I 1 × F I 2 × … F I C } ↦ F I 0 {\displaystyle {\mathcal {T}}:\{{\mathbb {F} }^{I_{1}}\times {\mathbb {F} }^{I_{2}}\times \ldots {\mathbb {F} }^{I_{C}}\}\mapsto {\mathbb {F} }^{I_{0}}} Here, C {\displaystyle C} and I 0 , I 1 , … , I C {\displaystyle I_{0},I_{1},\ldots ,I_{C}} are positive integers, and ( C + 1 ) {\displaystyle (C+1)} is the number of modes of a tensor (also known as the number of ways of a multi-way array). The dimensionality of mode c {\displaystyle c} is I c {\displaystyle I_{c}} , for 0 ≤ c ≤ C {\displaystyle 0\leq c\leq C} . In statistics and machine learning, an image is vectorized when viewed as a single observation, and a collection of vectorized images is organized as a "data tensor". For example, a set of facial images { d i p , i e , i l , i v ∈ R I X } {\displaystyle \{{\mathbb {d} }_{i_{p},i_{e},i_{l},i_{v}}\in {\mathbb {R} }^{I_{X}}\}} with I X {\displaystyle I_{X}} pixels that are the consequences of multiple causal factors, such as a facial geometry i p ( 1 ≤ i p ≤ I P ) {\displaystyle i_{p}(1\leq i_{p}\leq I_{P})} , an expression i e ( 1 ≤ i e ≤ I E ) {\displaystyle i_{e}(1\leq i_{e}\leq I_{E})} , an illumination condition i l ( 1 ≤ i l ≤ I L ) {\displaystyle i_{l}(1\leq i_{l}\leq I_{L})} , and a viewing condition i v ( 1 ≤ i v ≤ I V ) {\displaystyle i_{v}(1\leq i_{v}\leq I_{V})} may be organized into a data tensor (ie. multiway array) D ∈ R I X × I P × I E × I L × V {\displaystyle {\mathcal {D}}\in {\mathbb {R} }^{I_{X}\times I_{P}\times I_{E}\times I_{L}\times V}} where I P {\displaystyle I_{P}} are the total number of facial geometries, I E {\displaystyle I_{E}} are the total number of expressions, I L {\displaystyle I_{L}} are the total number of illumination conditions, and I V {\displaystyle I_{V}} are the total number of viewing conditions. Tensor factorizations methods such as TensorFaces and multilinear (tensor) independent component analysis factorizes the data tensor into a set of vector spaces that span the causal factor representations, where an image is the result of tensor transformation T {\displaystyle {\mathcal {T}}} that maps a set of causal factor representations to the pixel space. Another approach to using tensors in machine learning is to embed various data types directly. For example, a grayscale image, commonly represented as a discrete 2-way array D ∈ R I R X × I C X {\displaystyle {\mathbf {D} }\in {\mathbb {R} }^{I_{RX}\times I_{CX}}} with dimensionality I R X × I C X {\displaystyle I_{RX}\times I_{CX}} where I R X {\displaystyle I_{RX}} are the number of rows and I C X {\displaystyle I_{CX}} are the number of columns. When an image is treated as 2-way array or 2nd order tensor (i.e. as a collection of column/row observations), tensor factorization methods compute the image column space, the image row space and the normalized PCA coefficients or the ICA coefficients. Similarly, a color image with RGB channels, D ∈ R N × M × 3 . {\displaystyle {\mathcal {D}}\in \mathbb {R} ^{N\times M\times 3}.} may be viewed as a 3rd order data tensor or 3-way array.-------- In natural language processing, a word might be expressed as a vector v {\displaystyle v} via the Word2vec algorithm. Thus v {\displaystyle v} becomes a mode-1 tensor v ↦ A ∈ R N . {\displaystyle v\mapsto {\mathcal {A}}\in \mathbb {R} ^{N}.} The embedding of subject-object-verb semantics requires embedding relationships among three words. Because a word is itself a vector, subject-object-verb semantics could be expressed using mode-3 tensors v a × v b × v c ↦ A ∈ R N × N × N . {\displaystyle v_{a}\times v_{b}\times v_{c}\mapsto {\mathcal {A}}\in \mathbb {R} ^{N\times N\times N}.} In practice the neural network designer is primarily concerned with the specification of embeddings, the connection of tensor layers, and the operations performed on them in a network. Modern machine learning frameworks manage the optimization, tensor factorization and backpropagation automatically. === As unit values === Tensors may be used as the unit values of neural networks which extend the concept of scalar, vector and matrix values to multiple dimensions. The output value of single layer unit y m {\displaystyle y_{m}} is the sum-product of its input units and the connection weights filtered through the activation function f {\displaystyle f} : y m = f ( ∑ n x n u m , n ) , {\displaystyle y_{m}=f\left(\sum _{n}x_{n}u_{m,n}\right),} where y m ∈ R .
Gonioreflectometer
A gonioreflectometer is a device for measuring a bidirectional reflectance distribution function (BRDF). The device consists of a light source illuminating the material to be measured and a sensor that captures light reflected from that material. The light source should be able to illuminate and the sensor should be able to capture data from a hemisphere around the target. The hemispherical rotation dimensions of the sensor and light source are the four dimensions of the BRDF. The 'gonio' part of the word refers to the device's ability to measure at different angles. Several similar devices have been built and used to capture data for similar functions. Most of these devices use a camera instead of the light intensity-measuring sensor to capture a two-dimensional sample of the target. Examples include: a spatial gonioreflectometer for capturing the SBRDF (McAllister, 2002). a camera gantry for capturing the light field (Levoy and Hanrahan, 1996). an unnamed device for capturing the bidirectional texture function (Dana et al., 1999).
Event store
An event store is a type of database optimized for storage of events. Conceptually, an event store records only the events affecting an entity, dossier, or policy, and the state of the entity at any point in its history can be reconstructed by replaying its contributing events in sequential order. Events (and their corresponding data) are the only "real" facts that should be stored in the database. All other objects can be derived from these events, meaning they are instantiated in memory by runtime code as needed (e.g. for showing in a user interface). In theory, any object that aggregates over recorded event data is not stored in the database. Instead these objects are built 'on the fly', by traversing the event history. When the aggregated object instance is no longer needed, it can simply be discarded (released from memory). == Example with insurance policies == For example, the event store concept of a database can be applied to insurance policies or pension dossiers. In these policies or dossiers the instantiation of each object that make up the dossier or policy (the person, partner(s), employments, etc.) can be derived and can be instantiated in memory based on the real world events. == Double timeline == A crucial part of an event store database is that each event has a double timeline: This enables event stores to correct errors of events that have been entered into the event store database before. The two dates are: Valid date is the date at which the event has become valid. Transaction date is the date at which the event is entered into the database. == Error correction == Another crucial part of an event store database is that events that are stored are not allowed to be changed. Once stored, also erroneous events are not changed anymore. The only way to change (or better: correct) these events is to instantiate a new event with the new values and using the double timeline. A correcting event would have the new values of the original event, with an event data of that corrected event, but a different transaction date. This mechanism ensures reproducibility at each moment in the time, even in the time period before the correction has taken place. It also allows to reproduce situations based on erroneous events (if required). == Advantages and disadvantages == One advantage of the event store concept is that handling the effects of back dated events (events that take effect before previous events and that may even invalidate them) is much easier. An event store will simplify the code in that rolling back erroneous situations and rolling up the new, correct situations is not needed anymore. Disadvantage may be that the code needs to re-instantiate all objects in memory based on the events each time a service call is received for a specific dossier or policy. == Compared to regular databases == In regular databases, handling backdated events to correct previous, erroneous events can be painful as it often results in rolling back all previous, erroneous transactions and objects and rolling up the new, correct transactions and objects. In an event store, only the new event (and its corresponding facts) are stored. The code will then redetermine the transactions and objects based on the new facts in memory.
Database virtualization
Database virtualization is the decoupling of the database layer, which lies between the storage and application layers within the application stack. Virtualization of the database layer enables a shift away from the physical, toward the logical or virtual. Virtualization enables compute and storage resources to be pooled and allocated on demand. This enables both the sharing of single server resources for multi-tenancy, as well as the pooling of server resources into a single logical database or cluster. In both cases, database virtualization provides increased flexibility, more granular and efficient allocation of pooled resources, and more scalable computing. == Virtual data partitioning == The act of partitioning data stores as a database grows has been in use for several decades. There are two primary ways that data has been partitioned inside legacy data management systems: Shared-data databases: an architecture that assumes all database cluster nodes share a single partition. Inter-node communications are used to synchronize update activities performed by different nodes on the cluster. Shared-data data management systems are limited to single-digit node clusters. Shared-nothing databases: an architecture in which all data is segregated to internally managed partitions with clear, well-defined data location boundaries. Shared-nothing databases require manual partition management. In virtual partitioning, logical data is abstracted from physical data by autonomously creating and managing large numbers of data partitions (100s to 1000s). Because they are autonomously maintained, the resources required to manage the partitions are minimal. This kind of massive partitioning results in: Partitions that are small, efficiently managed, and load-balanced. Systems that do not require re-partitioning events to define additional partitions, even when the hardware is changed. “Shared-data” and “shared-nothing” architectures allow scalability through multiple data partitions and cross-partition querying and transaction processing without full partition scanning. == Horizontal data partitioning == Partitioning database sources from consumers is a fundamental concept. With greater numbers of database sources, inserting a horizontal data virtualization layer between the sources and consumers helps address this complexity. Rick van der Lans, the author of multiple books on SQL and relational databases, has defined data virtualization as "the process of offering data consumers a data access interface that hides the technical aspects of stored data, such as location, storage structure, API, access language, and storage technology." == Advantages == Added flexibility and agility for existing computing infrastructure. Enhanced database performance. Pooling and sharing computing resources, either splitting them (multi-tenancy) or combining them (clustering). Simplification of administration and management. Increased fault tolerance.
Autognostics
Autognostics is a new paradigm that describes the capacity for computer networks to be self-aware. It is considered one of the major components of Autonomic Networking. == Introduction == One of the most important characteristics of today's Internet that has contributed to its success is its basic design principle: a simple and transparent core with intelligence at the edges (the so-called "end-to-end principle"). Based on this principle, the network carries data without knowing the characteristics of that data (e.g., voice, video, etc.) - only the end-points have application-specific knowledge. If something goes wrong with the data, only the edge may be able to recognize that since it knows about the application and what the expected behavior is. The core has no information about what should happen with that data - it only forwards packets. Although an effective and beneficial attribute, this design principle has also led to many of today's problems, limitations, and frustrations. Currently, it is almost impossible for most end-users to know why certain network-based applications do not work well and what they need to do to make it better. Also, network operators who interact with the core in low-level terms such as router configuration have problems expressing their high-level goals into low-level actions. In high-level terms, this may be summarized as a weak coupling between the network and application layers of the overall system. As a consequence of the Internet end-to-end principle, the network performance experienced by a particular application is difficult to attribute based on the behavior of the individual elements. At any given moment, the measure of performance between any two points is typically unknown and applications must operate blindly. As a further consequence, changes to the configuration of given element, or changes in the end-to-end path, cannot easily be validated. Optimization and provisioning cannot then be automated except against only the simplest design specifications. There is an increasing interest in Autonomic Networking research, and a strong conviction that an evolution from the current networking status quo is necessary. Although to date there have not been any practical implementations demonstrating the benefits of an effective autonomic networking paradigm, there seems to be a consensus as to the characteristics which such implementations would need to demonstrate. These specifically include continuous monitoring, identifying, diagnosing and fixing problems based on high-level policies and objectives. Autognostics, as a major part of the autonomic networking concept, intends to bring networks to a new level of awareness and eliminate the lack of visibility which currently exists in today's networks. == Definition == Autognostics is a new paradigm that describes the capacity for computer networks to be self-aware, in part and as a whole, and dynamically adapt to the applications running on them by autonomously monitoring, identifying, diagnosing, resolving issues, subsequently verifying that any remediation was successful, and reporting the impact with respect to the application's use (i.e., providing visibility into the changes to networks and their effects). Although similar to the concept of network awareness, i.e., the capability of network devices and applications to be aware of network characteristics (see References section below), it is noteworthy that autognostics takes that concept one step further. The main difference is the auto part of autognostics, which entails that network devices are self-aware of network characteristics, and have the capability to adapt themselves as a result of continuous monitoring and diagnostics. == Path to autognostics == Autognostics, or in other words deep self-knowledge, can be best described as the ability of a network to know itself and the applications that run on it. This knowledge is used to autonomously adapt to dynamic network and application conditions such as utilization, capacity, quality of service/application/user experience, etc. In order to achieve autognosis, networks need a means to: Continuously monitor/test the network for application-specific performance Analyze the monitoring/test data to detect problems (e.g., performance degradation) Diagnose, identify and localize sources of degradation Automatically take actions to resolve problems via remediation/provisioning Verify the problems have been resolved (potentially rolling back changes if ineffective) Subsequently, continue to monitor/test for performance
Adrozek
Adrozek is malware that injects fake ads into online search results. Microsoft announced the malware threat on 10 December 2020, and noted that many different browsers are affected, including Google Chrome, Microsoft Edge, Mozilla Firefox and Yandex Browser. The malware was first detected in May 2020 and, at its peak in August 2020, controlled over 30,000 devices a day. But during the December 2020 announcement, Microsoft claimed "hundreds of thousands" of infected devices worldwide between May and September 2020. According to Microsoft, if not detected and blocked, Adrozek adds browser extensions, modifies a specific DLL per target browser, and changes browser settings to insert additional, unauthorized ads into web pages, often on top of legitimate ads from search engines. For each user tricked into clicking on the fake ads, the scammers earn affiliate advertising dollars. The malware has been observed to extract device data and, in some cases, steal credentials, sending them to remote servers. Users may unintentionally install the malware because of a drive-by download, by visiting a tampered website, opening an e-mail attachment, or clicking on a deceptive link or a deceptive pop-up window. The main malware program is downloaded to the “Programs Files” folder using file names such as Audiolava.exe, QuickAudio.exe, and converter.exe. According to PC Magazine, a good way to avoid, or mitigate, infection by Adrozek is to keep browser and related software programs up to date.