In computer science, a deterministic acyclic finite state automaton (DAFSA), is a data structure that represents a set of strings, and allows for a query operation that tests whether a given string belongs to the set in time proportional to its length. Algorithms exist to construct and maintain such automata, while keeping them minimal. DAFSA is the rediscovery of a data structure called Directed Acyclic Word Graph (DAWG), although the same name had already been given to a different data structure which is related to suffix automaton. A DAFSA is a special case of a finite state recognizer that takes the form of a directed acyclic graph with a single source vertex (a vertex with no incoming edges), in which each edge of the graph is labeled by a letter or symbol, and in which each vertex has at most one outgoing edge for each possible letter or symbol. The strings represented by the DAFSA are formed by the symbols on paths in the graph from the source vertex to any sink vertex (a vertex with no outgoing edges). In fact, a deterministic finite state automaton is acyclic if and only if it recognizes a finite set of strings. == History == Blumer et al first defined terminology Directed Acyclic Word Graph (DAWG) in 1983. Appel and Jacobsen used the same naming for a different data structure in 1988. Independent of earlier work, Daciuk et al rediscovered the latter data structure in 2000 but called it DAFSA. == Comparison to tries == By allowing the same vertices to be reached by multiple paths, a DAFSA may use significantly fewer vertices than the strongly related trie data structure. Consider, for example, the four English words "tap", "taps", "top", and "tops". A trie for those four words would have 12 vertices, one for each of the strings formed as a prefix of one of these words, or for one of the words followed by the end-of-string marker. However, a DAFSA can represent these same four words using only six vertices vi for 0 ≤ i ≤ 5, and the following edges: an edge from v0 to v1 labeled "t", two edges from v1 to v2 labeled "a" and "o", an edge from v2 to v3 labeled "p", an edge v3 to v4 labeled "s", and edges from v3 and v4 to v5 labeled with the end-of-string marker. There is a tradeoff between memory and functionality, because a standard DAFSA can tell you if a word exists within it, but it cannot point you to auxiliary information about that word, whereas a trie can. The primary difference between DAFSA and trie is the elimination of suffix and infix redundancy in storing strings. The trie eliminates prefix redundancy since all common prefixes are shared between strings, such as between doctors and doctorate the doctor prefix is shared. In a DAFSA common suffixes are also shared, for words that have the same set of possible suffixes as each other. For dictionary sets of common English words, this translates into major memory usage reduction. Because the terminal nodes of a DAFSA can be reached by multiple paths, a DAFSA cannot directly store auxiliary information relating to each path, e.g. a word's frequency in the English language. However, if for each node we store the number of unique paths through that point in the structure, we can use it to retrieve the index of a word, or a word given its index. The auxiliary information can then be stored in an array.
World Database of Happiness
The World Database of Happiness is a web-based archive of research findings on subjective appreciation of life, based in the Erasmus Happiness Economics Research Organization of the Erasmus University Rotterdam in The Netherlands. The database contains both an overview of scientific publications on happiness and a digest of research findings. Happiness is defined as the degree to which an individual judges the quality of his or her life as a whole favorably. Two 'components' of happiness are distinguished: hedonic level of affect (the degree to which pleasant affect dominates) and contentment (perceived realization of wants). == Aims == The World Database of Happiness is a tool to quickly acquire an overview on the ever-growing stream of research findings on happiness Medio 2023 the database covered some 16,000 scientific publications on happiness, from which were extracted 23,000 distributional findings (on how happy people are) and another 24,000 correlational findings (on factors associated with more and less happiness). The first findings date from 1915. == Technique == The World Database of Happiness is a ‘findings archive’, which consists of electronic ‘finding pages’ on which separate research results are described in a standard format and terminology. These finding pages can be selected on various characteristics, such as population studies, the measure of happiness used and observed co-variates. All finding-pages have a specific internet address to which links can be made in scientific review papers or policy recommendations. This allows a concise presentation of many findings in a table, while providing readers with access to detail. == Scientific use == The Database has been cited in 254 scientific papers, for example to access under what conditions economic growth enhances average happiness or to show that rising mean happiness at first raises happiness inequality, but further rise will diminish these differences, or that healthy eating is associated with more happiness, even after controlling for the effect on health Another finding is that relative simple happiness training techniques raise happiness by some 5% == Popular use == The World Database of Happiness is often used by popular media to make lists of the happiest countries around the globe. An example is the Happy Planet Index, which aims to chart sustainable happiness all over the world by combining data on longevity, happiness and the size of the ecological footprint of citizens. == Strengths and weaknesses == The database has a clear conceptual focus, it includes only research findings on subjective enjoyment of one's life as a whole. Thereby it evades the Babel that has haunted the study of happiness for ages. The other side of that coin is that much interesting research is left out. The findings are reported with technical details about measurement and statistical analysis. This detail is welcomed by scholars, but makes the information difficult to digest for lay-persons. Still another limitation is that the determinants of happiness appear to vary considerably across persons and situations, which make it hard to draw general conclusions about the causes of happiness. What is clear is that poor health, separation, unemployment and lack of social contact are all strongly negatively associated with happiness. Another problem for the World database of happiness is that the studies on happiness increase with such a high rate that it gets increasingly difficult to offer a complete overview of all research findings. A further concern is that the Database of Happiness is exclusively focused on hedonic happiness (feeling good) and not on mature happiness that might exist in the face of suffering
Protocol Builder
Protocol Builder is a tool in programming languages to generate code to build protocols in a fast and reliable way. Network programming for all kinds of protocols (such as TCP, UDP, and SNMP) includes converting data to be transferred to raw bytes in the sending side and parsing these bytes in the receiving side. Protocol builders facilitate this stage, usually by automatically generating the code. Protocol Programming has many components to be developed, these are: server listener, server connection, client connection, packets, and loggers. Most protocol builders implement these components automatically so developers save time and money. Currently, there are two Protocol Builders in the market, one for C++ from UpRedSun which is for TCP and UDP protocols. The second one is for .Net languages which generates the code in C# for TCP Protocols, this tool is called .Net Protocol Builder.
Twproject
Twproject (say: T W Project) is a web-based project and groupware management tool created by Open Lab, an Italian software house founded in 2001. It won the 17th Jolt Productivity Award in 2007 in the project management category. In March 2019 it becomes property of Twproject company. It has widespread use in universities as a teaching tool in project management courses. It is used by Oracle Corporation, Prada, Calzedonia, General Electric and many other companies from corporations to small start-ups. == History == April 2001 - The idea of Teamwork came to Open-Lab founders from a need to overcome the PM tools used at that time. It was built in Microsoft ASP and Adobe Flash November 2002 - Open-Lab decide to move from Flash to HTML and from ASP to Java-JSP. Teamwork 2 development is started. June 2004 - Teamwork 2 released, using top open-source technologies like Hibernate, jBlooming, dynamic CSS, Ajax 7 January 2005 - Teamwork goes open source, under LGPL license; remains such until June 2006 (18 months): it is a hit application on SourceForge, with 38.000 downloads, covered by greeting but starving April 2005 - Open-Lab takes the decision to change commercial strategy to finance development of Teamwork version 3 6 June 2006 - Teamwork 3 is finally out (15 months development). New interface, many new features, agile support and much more 27 March 2007 - Teamwork wins the 2007 JOLT Productivity Awards for project management category July 2007 - Teamwork 4 development started: new interface, extended use of new HTML capabilities, JS-oriented interface, start using jQuery February 2009 - Teamwork 4.0 is out February 2010 - Teamwork 4.4: public project pages, Chinese interface. jQuery is getting more space in Teamwork December 2010 - Teamwork 4.6: released Mobile module available for iPhone, Android, BlackBerry. Intensive usage of jQuery June 2011 - Teamwork 4.7: released Issue Kanban / Organizer January 2012 - Teamwork 5.0 development started. Lighter interface, extensive usage of dynamic pages, easier installer and first time approach. Learning curve highly reduced. A jQuery Gantt editor included and released free for the community July 2012 - Teamwork 5 released and also the free online Gantt editor November 2012 - Teamwork 5.1 with new trees and improved model for staffing March 2013 - Teamwork 5.2 with stronger support for customizations and Japanese interface. April 2014 - Teamwork has changed its name in Twproject because the domain teamwork.com has been purchased by Teamwork. April 2013 - Twproject 5.4 with a redesigned more powerful Gantt chart. August 2015 - Twproject 5 finale release. September 2015 - Twproject 6 with a completely redesigned user interface. March 2019 - A new company Twproject srl has been spun off. September 2021 - Twproject 7 has been released introducing WBS based management and workload management. == Features == Project & task management (with Microsoft Project import/export), and JSON format Gantt editor. Uses jQuery Gantt components Time tracking. Several entry points: dashboard, weekly view, issues, start/stop buttons Resource planning with weekly/monthly view, work load overview, unavailability from agenda Issue tracking & planning(with Kanban), e-mail integration, task dedicated inboxes Dashboard configuration, with customizable portlets and layout Message boards Scrum module Meeting and minute management, attached documents Agenda (Integrates with iCal, Microsoft Outlook, Microsoft Entourage, and Google Calendar) Document management, remote file systems link with NTFS, FTP, SVN, S3 (Dropbox, Google drive) Mobile application for iPhone, iPad, Android, Blackberry, Windows phone == Integration == A complete JSON API is available for integrations. The applications runs in Java JDK 8+ on the Hibernate object/relational mapping. The standard distribution uses Apache Tomcat 9, but can run on any J2EE application server. Twproject is tested on these DB servers: MySQL, Oracle, SQL Server, PostgreSql, HSQLDB, but as uses Hibernate can run on many others. There is simple graphical step-by-step installer for Windows, Mac, Linux, .zip/.tar.gz/.rpm packages.
Digital image correlation and tracking
Digital image correlation and tracking is an optical method that employs tracking and image registration techniques for accurate 2D and 3D measurements of changes in 2D images or 3D volumes. This method is often used to measure full-field displacement and strains, and it is widely applied in many areas of science and engineering. Compared to strain gauges and extensometers, digital image correlation methods provide finer details about deformation, due to the ability to provide both local and average data. == Overview == Digital image correlation (DIC) techniques have been increasing in popularity, especially in micro- and nano-scale mechanical testing applications due to their relative ease of implementation and use. Advances in computer technology and digital cameras have been the enabling technologies for this method and while white-light optics has been the predominant approach, DIC can be and has been extended to almost any imaging technology. The concept of using cross-correlation to measure shifts in datasets has been known for a long time, and it has been applied to digital images since at least the early 1970s. The present-day applications are almost innumerable, including image analysis, image compression, velocimetry, and strain estimation. Much early work in DIC in the field of mechanics was led by researchers at the University of South Carolina in the early 1980s and has been optimized and improved in recent years. Commonly, DIC relies on finding the maximum of the correlation array between pixel intensity array subsets on two or more corresponding images, which gives the integer translational shift between them. It is also possible to estimate shifts to a finer resolution than the resolution of the original images, which is often called "sub-pixel" registration because the measured shift is smaller than an integer pixel unit. For sub-pixel interpolation of the shift, other methods do not simply maximize the correlation coefficient. An iterative approach can also be used to maximize the interpolated correlation coefficient by using non-linear optimization techniques. The non-linear optimization approach tends to be conceptually simpler and can handle large deformations more accurately, but as with most nonlinear optimization techniques, it is slower. The two-dimensional discrete cross correlation r i j {\displaystyle r_{ij}} can be defined in several ways, one possibility being: r i j = ∑ m ∑ n [ f ( m + i , n + j ) − f ¯ ] [ g ( m , n ) − g ¯ ] ∑ m ∑ n [ f ( m , n ) − f ¯ ] 2 ∑ m ∑ n [ g ( m , n ) − g ¯ ] 2 . {\displaystyle r_{ij}={\frac {\sum _{m}\sum _{n}[f(m+i,n+j)-{\bar {f}}][g(m,n)-{\bar {g}}]}{\sqrt {\sum _{m}\sum _{n}{[f(m,n)-{\bar {f}}]^{2}}\sum _{m}\sum _{n}{[g(m,n)-{\bar {g}}]^{2}}}}}.} Here f(m, n) is the pixel intensity or the gray-scale value at a point (m, n) in the original image, g(m, n) is the gray-scale value at a point (m, n) in the translated image, f ¯ {\displaystyle {\bar {f}}} and g ¯ {\displaystyle {\bar {g}}} are mean values of the intensity matrices f and g respectively. However, in practical applications, the correlation array is usually computed using Fourier-transform methods, since the fast Fourier transform is a much faster method than directly computing the correlation. F = F { f } , G = F { g } . {\displaystyle \mathbf {F} ={\mathcal {F}}\{f\},\quad \mathbf {G} ={\mathcal {F}}\{g\}.} Then taking the complex conjugate of the second result and multiplying the Fourier transforms together elementwise, we obtain the Fourier transform of the correlogram, R {\displaystyle \ R} : R = F ∘ G ∗ , {\displaystyle R=\mathbf {F} \circ \mathbf {G} ^{},} where ∘ {\displaystyle \circ } is the Hadamard product (entry-wise product). It is also fairly common to normalize the magnitudes to unity at this point, which results in a variation called phase correlation. Then the cross-correlation is obtained by applying the inverse Fourier transform: r = F − 1 { R } . {\displaystyle \ r={\mathcal {F}}^{-1}\{R\}.} At this point, the coordinates of the maximum of r i j {\displaystyle r_{ij}} give the integer shift: ( Δ x , Δ y ) = arg max ( i , j ) { r } . {\displaystyle (\Delta x,\Delta y)=\arg \max _{(i,j)}\{r\}.} == Deformation mapping == For deformation mapping, the mapping function that relates the images can be derived from comparing a set of subwindow pairs over the whole images. (Figure 1). The coordinates or grid points (xi, yj) and (xi, yj) are related by the translations that occur between the two images. If the deformation is small and perpendicular to the optical axis of the camera, then the relation between (xi, yj) and (xi, yj) can be approximated by a 2D affine transformation such as: x ∗ = x + u + ∂ u ∂ x Δ x + ∂ u ∂ y Δ y , {\displaystyle x^{}=x+u+{\frac {\partial u}{\partial x}}\Delta x+{\frac {\partial u}{\partial y}}\Delta y,} y ∗ = y + v + ∂ v ∂ x Δ x + ∂ v ∂ y Δ y . {\displaystyle y^{}=y+v+{\frac {\partial v}{\partial x}}\Delta x+{\frac {\partial v}{\partial y}}\Delta y.} Here u and v are translations of the center of the sub-image in the X and Y directions respectively. The distances from the center of the sub-image to the point (x, y) are denoted by Δ x {\displaystyle \Delta x} and Δ y {\displaystyle \Delta y} . Thus, the correlation coefficient rij is a function of displacement components (u, v) and displacement gradients ∂ u ∂ x , ∂ u ∂ y , ∂ v ∂ x , ∂ v ∂ y . {\displaystyle {\frac {\partial u}{\partial x}},{\frac {\partial u}{\partial y}},{\frac {\partial v}{\partial x}},{\frac {\partial v}{\partial y}}.} DIC has proven to be very effective at mapping deformation in macroscopic mechanical testing, where the application of specular markers (e.g. paint, toner powder) or surface finishes from machining and polishing provide the needed contrast to correlate images well. However, these methods for applying surface contrast do not extend to the application of free-standing thin films for several reasons. First, vapor deposition at normal temperatures on semiconductor grade substrates results in mirror-finish quality films with RMS roughnesses that are typically on the order of several nanometers. No subsequent polishing or finishing steps are required, and unless electron imaging techniques are employed that can resolve microstructural features, the films do not possess enough useful surface contrast to adequately correlate images. Typically this challenge can be circumvented by applying paint that results in a random speckle pattern on the surface, although the large and turbulent forces resulting from either spraying or applying paint to the surface of a free-standing thin film are too high and would break the specimens. In addition, the sizes of individual paint particles are on the order of μms, while the film thickness is only several hundred nanometers, which would be analogous to supporting a large boulder on a thin sheet of paper. == Digital volume correlation == Digital Volume Correlation (DVC, and sometimes called Volumetric-DIC) extends the 2D-DIC algorithms into three dimensions to calculate the full-field 3D deformation from a pair of 3D images. This technique is distinct from 3D-DIC, which only calculates the 3D deformation of an exterior surface using conventional optical images. The DVC algorithm is able to track full-field displacement information in the form of voxels instead of pixels. The theory is similar to above except that another dimension is added: the z-dimension. The displacement is calculated from the correlation of 3D subsets of the reference and deformed volumetric images, which is analogous to the correlation of 2D subsets described above. DVC can be performed using volumetric image datasets. These images can be obtained using confocal microscopy, X-ray computed tomography, Magnetic Resonance Imaging or other techniques. Similar to the other DIC techniques, the images must exhibit a distinct, high-contrast 3D "speckle pattern" to ensure accurate displacement measurement. DVC was first developed in 1999 to study the deformation of trabecular bone using X-ray computed tomography images. Since then, applications of DVC have grown to include granular materials, metals, foams, composites and biological materials. To date it has been used with images acquired by MRI imaging, Computer Tomography (CT), micro-CT, confocal microscopy, and lightsheet microscopy. DVC is currently considered to be ideal in the research world for 3D quantification of local displacements, strains, and stress in biological specimens. It is preferred because of the non-invasiveness of the method over traditional experimental methods. Two of the key challenges are improving the speed and reliability of the DVC measurement. The 3D imaging techniques produce noisier images than conventional 2D optical images, which reduces the quality of the displacement measurement. Computational speed is restricted by the file sizes of 3D images, which are significantly larger than 2D images. For example, an
E-on Vue
Vue is a software tool for world generation by Bentley Systems, with support for many visual effects, animations, and various other features. The tool has been used in several feature-length films. In 2024, Bentley Systems announced that Vue would be discontinued, and be freely available to those that still wish to use it. == Versions == == Features == This is a list of features as of the 2023 release of Vue: === Terrains === Heightfield terrains Procedural terrains Infinite terrains Planetary terrains Real-world terrains 3D terrain sculpting Terrain export === EcoSystem Instancing Technology === Material-based EcoSystems Global EcoSystems Dynamic EcoSystems 360° EcoSystem Population Paint EcoSystem instances EcoParticles Export EcoSystem populations === Vegetation === Built-in Plant editor Compatible with PlantFactory Vegetation assets === Atmosphere, Skies and Clouds === Standard atmospheric model Spectral atmospheric model Photometric atmospheric model Atmosphere presets Procedural Volumetric 3D cloud layers Standalone 3D Metaclouds Convert meshes to Clouds Cloud morphing Import OpenVDB Export standalone and cloud layer zones to OpenVDB Export skies as HDRI === Modeling === Primitive and Feature modeling 3D Text edition tool Metablobbing Hyperblobs Export baked hyperblobs Splines Built in Road Construction toolkit Random rock generator Export rocks === Texturing and UVs === Material presets PBR Substance support Node-based procedural materials Volumetric materials and Hypertextures Stacked UVs Unwrapped UVs Ptex === Interoperability, Integration And Export === Export single assets to generic 3D formats Full scene export Integration plugins Import and Export Camera data as FBX and Nuke.chan Python API ZBrush GoZ bridge === Animation === Animate objects, materials, atmospheres, clouds, waves... Automatic wind and breeze Localized wind effects per plant / per EcoSystem population Omni and directional ventilators for local modifications of plants Time spline editor Automatic keyframe creation Automatic synchronization of cameras and lights Animation export as AfterEffects Import motion tracking information === Lighting === Global illumination, Global Radiosity, Ambient occlusion Subsurface Scattering HDRI image based lighting Point light, Quadratic point light, Spotlight, Quadratic spotlight, Directional light Use IES distribution profiles on photometric lights Area lights, light panels, light portals Physically accurate caustics computation === Rendering === Render with Ray Tracer Render with Path Tracer Stereoscopic rendering 360/180 VR Panorama Render Option Spherical panoramic rendering Tone mapping options Multipass & G-Buffer Network rendering with HyperVue / RenderCows Network rendering with RenderNodes == Users == Blue Sky Studios Digital Domain DreamWorks Animation: Kung Fu Panda Industrial Light & Magic: Indiana Jones and the Kingdom of the Crystal Skull, Pirates of the Caribbean: Dead Man's Chest Sony Pictures Imageworks Warner Bros. Interactive Entertainment Weta Digital
Digital transaction management
Digital transaction management (DTM) is a category of cloud services designed to digitally manage document-based transactions. DTM removes the friction inherent in transactions that involve people, documents, and data to create faster, easier, more convenient, and secure processes. DTM goes beyond content and document management to include e-signatures, authentication and non-repudiation; enabling co-browsing between the customer and the business; document transfer and certification; secure archiving that goes beyond records management; and a variety of meta-processes around managing electronic transactions and the documents associated with them. DTM standards are proposed and managed by the xDTM Standard Association Aragon Research has estimated that "by YE 2016, 70% of large enterprises will have a DTM initiative underway or fully implemented."